The Raspberry Pi 4 needs a fan

https://www.jeffgeerling.com/blog/2019/raspberry-pi-4-needs-fan-heres-why-and-how-you-can-add-one

by geerlingguy • 7 years ago

566 277 7 years ago

I'd guess that heatsink and a case with heatpipes would be sufficient for most, though perhaps not all, uses and silent, which for me is pretty important on a Raspberry Pi

seanhandley6• 7 years ago

I tried a heatsink but it didn't really help unless I had a desk fan providing some air flow.

gadgetoid3• 7 years ago

This pretty much lines up with my findings. I popped the pre-installed heat-spreader off and applied a heatsink with noctua thermal paste... basically no difference- step-by-step chaos here: https://twitter.com/Gadgetoid/status/1151442153584910337

Just adding a small fan (trying to avoid blowing our own trumpet too much here) absolutely demolishes the cooling performance of any reasonably-sized heatsink. Presumably there's just not that much passive airflow over something an inch square, even with convection.

I still wonder what would happen if a full desktop-sized heatsink was coupled to the Pi 4's SOC.

bjoli4• 7 years ago

did you try a big enough heatsink? I put a northbridge heatsink on my odroid xu4, and it did even better than the stock cooler with a small fan.

geerlingguy13• 7 years ago

The problem is there are now a number of chips on the board—many of which are too small to pop a heatsink on them—which get crazy hot. If you have the Pi inside any kind of enclosed case, that heat just bakes everything else, even if you have heat sinks.

0815test• 7 years ago

You could design a copper heat-spreader to pop over the heat-sensitive part(s) of the board, and then apply a heatsink to that. Maybe copper foil would do the job.

Another approach is to just run the Pi submersed in mineral oil, with liquid convection then taking the heat away from the board and shedding it to the surrounding environment. We usually don't run our electronics like this (even though the general approach is widely used for cooling needs of all sorts) because mineral oil is gross and might even impact the endurance of our hardware - but the Pi is tiny and cheap enough to make this a non-issue.

Someone1234• 7 years ago

That's what Apple used to do with their Macbooks. Heat pipes into the metal frame which conducts it over a larger surface area creating natural convections which carry the heat into the air.

The real downside is that mass plays a substantial role. Meaning thicker metal, larger cases, are better than thinner/smaller. Whereas a fan can accomplish similar results for less cost and space (but not passively).

If people don't think passive can work they need to check out Apple's recent Mac Pro that passively cools two Radeon Pro 580Xs. There's no limit, except cost.

Personally I still feel a combination of heat pipe, into heat sink, with a small progressive fan is the ultimate. If it is large enough the fan should stay off except under heavy load.

vel0city• 7 years ago

While there are not extra fans on the cards themselves, I'd hardly call anything in the Mac Pro "passively cooled" considering there are three giant fans on the chassis immediately in front of those heatsinks.

HeWhoLurksLate4• 7 years ago

Apple has a pretty long history of passively cooled devices, including the G4 cube, which had a massive (for the time) CPU and GPU, if you wanted in it, was 8 inches cubed in volume, and cooled convectively.

seanhandley6• 7 years ago

I can recommend Pimoroni's fan shim. They provide a python project that allows you to set temperature thresholds to kick the fan in so it's not on all the time. It's not silent but it's pretty quiet.

https://github.com/pimoroni/fanshim-python

geerlingguy13• 7 years ago

I thought about getting one of these, as they are a little more turnkey... however I couldn’t find an easy way to purchase and get quick shipping in the US. Is there any other way besides ordering through the UK?

whiskers5• 7 years ago

Ahoy! We ship (pretty fast!) to the US. :-)

Failing that I'd hope Adafruit will have them in stock soon! I'm one of the co-founders of Pimoroni, drop me a line if you need any other help.

rvz• 7 years ago

Indeed, the fan shim is insanely cool and I just bought one of these the moment that it was back in stock together with my Raspberry Pi 4. It also works on the Pi 3 and 2.

Here's the link if anyone's interested: https://shop.pimoroni.com/products/fan-shim

whiskers5• 7 years ago

Glad you like it! We think it's the best solution for cooling any model of Raspberry Pi that's available.

redwards510• 7 years ago

Cool fan but it says "not heatsink compatible", so if you are like me and attached the heatsinks that came free with your Pi case, you will be out of luck.

jtwigg• 7 years ago

I second this. The fan is amazing!

LeonM2• 7 years ago

So does the pi 3 if you stick it in a case, even with a heatsink.

I was using a pi 3 with a heatsink in the official case to play a h265 movie (which will be software decoded on a pi3). After about 10 minutes I noticed it started dropping frames and it displayed the thermometer symbol in the top-right of the display.

When I removed the top lid from the case, the temperature dropped enough for the thermometer icon to disappear and playback to continue smoothly.

teraflop• 7 years ago

Yeah, thermal insulation behaves in much the same way as electrical insulation. If you put a conductor in series with a resistor, the conductor doesn't conduct all that well.

TylerE• 7 years ago

Seems like the winning solution would be to do as Apple does and make the case the heatsink. Aluminum is a pretty good thermal conductor, and at the very least it'd get you lots of surface area.

dbg314152• 7 years ago

Over the years I've used Raspberry Pis as little media players, but they kept burning out every 3-4 months; the card reader (their SSD) wouldn't work, or they'd just blink some other error message. I thought they were just cheaply made ($35 after all). Anyway, long story short, I got a fan and the last one has been working for over a year without issues.

seanhandley6• 7 years ago

SD cards have a limited number of writes so if you have the OS constantly writing to it then eventually it sets itself read-only.

You can mitigate this somewhat with https://github.com/azlux/log2ram

With some finagling you can get them to boot an OS from an external disk then your SD card can just hold a read-only boot loader.

blackflame70002• 7 years ago

Also if you are not using a good power supply the Pi will happily operate on less current except when it needs that current during power-intensive operations like watching a movie. This could be causing silent corruption as it happened in my case. If you ever see a thunderbolt symbol best check your power supply.

dleslie• 7 years ago

Flirc makes excellent passive cooling cases for RPis. Basically the entire shell is a heat sink.

Works for me, all my little media boxes run happily with them, despite running 24/7.

mceachen• 7 years ago

I just found out you can pre-order pi 4 cases: http://blog.flirc.tv/index.php/2019/06/24/new-pi-4-cases/

(I don't have any monetary interest in flirc, I'm just another happy pi3 flirc case owner)

panda888882• 7 years ago

Same here. I have 2 Flirc cases for the RPi 3b, and it keeps it happy. One is used for media the other for emulator.

panda888882• 7 years ago

If anyone is interested in putting in a bulk order for Flirc Pi4 cases to save on shipping, let me know. I am in the San Diego area in SoCal.

danaos• 7 years ago

Well the pi3 does not support h265 acceleration natively, it should have been better to use it on h264 movies.

londons_explore• 7 years ago

Hardware acceleration comes in degrees... It's totally possible to hand-code some GPU firmware to decode any bitstream far more efficiently than the CPU can do it...

It's just a lot of work, and either Broadcom hasn't done it, or they don't want to license it to the Raspberry Pi.

LeonM2• 7 years ago

That is correct. A pi 4 can doe h265 acceleration, but for anything other than a pi 4, use h264 content.

nullbyte• 7 years ago

I'm hosting a Node.js webserver from my RPi3, I have heatsinks and a case installed with no fan.

Seems to run fine, it's never overheated or throttled for me.

Florin_Andrei• 7 years ago

I've a Pi3 with a CPU heatsink, in case. I have not seen it throttle after adding the radiator.

y04nn• 7 years ago

I installed libreelec on my Raspberry Pi 4 the first day I had it. The CPU immediately started (while playing 1080p video) to heat a lot to the point it stalled. Since I haded a motherboard chipset heatsink that I had laying around on the CPU it worked flowlessly. (I keep it without any case)

the_angry_angel2• 7 years ago

This was exactly my intended use case - as a gift for relatives - the problem I've had is that I need it enclosed to prevent tiny little fingers from getting hurt/destroying the thing. Tried soak testing it one night and experienced the same thing :/

Currently I'm hoping that I can modify the case this weekend to fulfill my needs.

As something intended to be used by kids to learn about computing I do wonder how many are going to get hurt fingers from the heat output by accidentally maxing the cpu and/or touching the USB ports, etc.

krisrm• 7 years ago

As something intended to be used by kids to learn about computing I do wonder how many are going to get hurt fingers from the heat output by accidentally maxing the cpu and/or touching the USB ports, etc.

Sounds like one of the unexpected lessons will be heat dissipation :)

Probably outside of the realm of weekend hacking, but I wonder if something like this would work for you: https://flirc.tv/more/raspberry-pi-4-case

Best of luck!

malensek• 7 years ago

Even the previous-gen Pis would easily throttle under load without a heat sink (although usually installing a decent heat sink was enough to resolve the problem, assuming decent airflow). As the article notes, the heat was mainly from the SoC in the past. The Pi 4 is on a whole different level indeed.

I imagine the logic here is the same as with many other Pi accessories: if you need it, you'll buy it or get it as part of a bundle. In some cases throttling is not a huge issue. But we're a far cry from the simple plug-and-play Pis of the past... Another issue is power -- you can't simply run the newer Pis reliably off any old cell phone charger you have laying around.

geerlingguy13• 7 years ago

That’s just it, though. The official Pi power supply is adequate and good for powering the Pi in any condition, but the case is a far cry from adequate. At best, it just toasts everything inside more evenly, at worst it contributes to throttling because now the heat from every other part of the Pi forms a hot thermal blanket over the CPU.

I’m amazed they didn’t at least add a few passive ventilation holes or slots, somewhere. It gets crazy hot inside the case.

isoprophlex2• 7 years ago

I'm sad about the case too, it needs some extensive Dremel work to allow prolonged database queries or movie transcoding or basically anything I'd like to use it for

devinjflick2• 7 years ago

Yeah snagging the official case was a big let down imo. Having to modify it just so the board will operate for a generic use case was a sad moment for me. Glad to see your solution though, time to bust out my old hole saw kit!

Also excited to follow your Dramble project!

vvanders• 7 years ago

Your phone will do this too, that's why sandwiching icepacks between your iPhone makes it do an iCloud backup faster.

Lots of vendors disable thermal limiting during benchmarks to get better numbers.

kingosticks7• 7 years ago

Part of me is wondering if that's why they disabled the 60C soft temperature limit for the pi 4...

AnIdiotOnTheNet3• 7 years ago

Yeah, I'm kinda wondering just what the Pi is supposed to be at this point. Is it still an inexpensive low power device for teaching basic computer science? Because it seems like it's more for making Kodi boxes or the worlds most powerful LED blinkers.

giobox• 7 years ago

I'd love to see some kind of reasonable data on the breakdown of how many Pis actually end up in education environments vs RetroPie/Kodi/PiHole/whatever else "service on an SD card image" turnkey solution type thing people use them for. At this point, my guess/gut feel is that education is an increasingly small part of the market for the Pi, yet appears to still be the main focus of the Pi Foundation.

I've always felt the educational focus was much more about the rose-tinted memories of parents who grew up in the homebrew computing generation in the UK. It feels much more a product for me in that regard than it does my kids. Ebon Upton et al are of this generation as well. British computer people of a certain age love to remember their ZX Spectrums etc.

marcosdumay2• 7 years ago

The Pi4 is overpowered for a Kodi box.

That said, there is a huge number of applications for overpowered LED blinkers, and no lack of people to use them. And there is a great deal of educational value on having those boards available and easy to get.

Besides, it's becoming hard to find people without access to a machine where they can learn basic computer science. So this one niche is closing down, while the Pi is still unbeatable on hardware hacking.

soneil2• 7 years ago

Why does it need to be either/or? The way I look at it, every single hobbyist, retropie, dust collector, etc is just enabling the scale that allows them to deliver the hardware at the price point.

If 100% of Pi went into schools, the foundation would likely have dried up 4 years ago. We might not be the target market, but we enable it. We enable the development, the third-party/after-market, we provide the community. The foundation provide the "noble goal", and we provide the cashflow.

hajile• 7 years ago

Raspberry Pi tower cooler -- the cooler we deserve.

https://www.seeedstudio.com/ICE-Tower-CPU-Cooling-Fan-for-Ra...

thoughtpalette2• 7 years ago

That link 404s for me unfortunately.

tacotime• 7 years ago

It's adorable!

https://webcache.googleusercontent.com/search?q=cache:k1aQeM...

gvb• 7 years ago

https://www.youtube.com/watch?v=l5IFD2wq_gA

Heat pipe, heatsink, and fan that is as big as the Pi! :-O

beckler• 7 years ago

well yeah, this thing pulls 3 amps.

even though it's mostly to push amperage down the USB 3.0 ports, those electrons going across the board are gonna generate some heat.

geerlingguy13• 7 years ago

Worst case (headless, at least) with a USB SSD powered off the bus, I was pulling 1.8 amps. But I can imagine if you’re also driving some other USB devices, and one or two HDMI displays, 3A is not far off!

sneak• 7 years ago

Has anyone made an RPi4 lava lamp yet? Extra credit if there is a camera built in that feeds into the camera connector that supplements the RNG.

vectorEQ2• 7 years ago

lava lamp / hw crypto module :'D match made in heaven

BaconJuice• 7 years ago

Just a bit off-topic but what are you guys doing that you need to do CPU throttling? I just got a Pi4 and wondering if I'm missing out on some cool projects I can do with it :)

geerlingguy13• 7 years ago

The Pi 4 is the first generation that's actually not horrible at running Kubernetes, so I'm mostly having fun with that (ongoing saga at www.pidramble.com).

cwyers• 7 years ago

Is this just about how fast the CPU is, or is there some other reason the k8s experience is better now?

milofeynman• 7 years ago

Are you planning on adding a fan to the cluster?

Negitivefrags• 7 years ago

We finally have enough performance that we can waste it with more layers. Hooray!

seanhandley6• 7 years ago

Home media server. Encoding 1080p video brings the temp up.

adrianmonk2• 7 years ago

If you run computing hardware at its thermal capacity for long periods of time, this will cause more wear on the parts than if they are run well inside their limits.

So I have a moderately increased likelihood of, at some indefinite point in the future, having to spend a whole $35 to replace the Raspberry Pi. I can prevent this by spending extra money (and time) up front.

In some cases, it might be worth it. Maybe I'm using this Pi to control something, so downtime is bad. (But even then, fans have moving parts and a high failure rate, so plan to monitor the fan's condition and be prepared to replace it.)

In other cases, if the performance isn't important to you, it may make more sense to just accept a shorter lifespan. By the time it breaks, the next generation Pi may be out anyway. I don't love thinking of hardware as disposable, but at this price point, it may be smarter economically.

spiderfarmer2• 7 years ago

I would accept the shorter lifespan just because of the fan noise. Small and cheap fans are very noticeable in otherwise quiet rooms. I'd hate it.

adrianmonk2• 7 years ago

I hate fan noise too. Sometimes it's necessary, though. But yeah, noise is another trade-off to consider.

Regarding Raspberry Pi specifically, larger, slow-moving fans tend to be quieter than smaller, fast-moving fans. The Pi is compact, so a small fan would be the natural choice.

pas2• 7 years ago

Big passive heatsink is not an option?

junaru• 7 years ago

If you run computing hardware at its thermal capacity for long periods of time, this will cause more wear on the parts than if they are run well inside their limits.

How true is this actually? Personal anecdote is an I5-2500K overclocked to 4.6ghz with budget aftermarket cooler (its at 4.6ghz constantly regardless of load). It's been running 24/7 in my desktop since 2011.

When will it fail? I see these disclaimers all the time and they sound logical, but does anyone have some numbers on these fail rates under these 'prolonged extreme loads'?

HeWhoLurksLate4• 7 years ago

I've been running a I7-6700K on a 120mm AIO radiator for three years. It gets loud, but it also smashes my OC results.

Personally, my biggest worry is the pump failing, and not the fans.

Bootwizard3• 7 years ago

Generally the time under load is the factor that kills parts, not just time on in general. For example: components that are constantly used for test benches to run benchmarks that pin them to 100% performance constantly will burn out much faster than your case.

Also, CPUs can get "binned" where you get the best CPUs in a batch which usually result in increased longevity and higher ceilings on overclocking. People usually call this the "Silicon Lottery". You may have just gotten lucky in your case and won the Silicon Lottery. That's honestly an impressive overclock for that CPU.

I've personally never had a component burn out before I want to upgrade it either, so I'd take that common "disclaimer" with a grain of salt. I think it really comes down to if you got a good bin or a bad bin part with any component.

NikolaeVarius• 7 years ago

Last time I checked, a consumer grade CPU has expected lifespan of 20-30 years, so your CPU is still in its young adult years

magicalhippo• 7 years ago

How true is this actually?

There's a nice write-up here[1]. To summarize, using the Arrhenius equation as an approximation, one roughly gets that a 10C increase in operating temperature leads to cutting the expected lifetime in half.

However this is a rough approximation and does not consider various other failure modes, such as those associated with thermal cycling.

It also does not really matter much when significantly below the rated max temps: 2000 years cut in half is still plenty...

The take-away seems to be that operating continuously near the max rated temperature can have a significant effect on expected lifetime. Also extreme thermal cycling is probably not a good idea either.

[1] https://www.electronics-cooling.com/2017/08/10c-increase-tem...

imtringued• 7 years ago

Probably in 20 years. The rasperry pi will probably fail in 100 years. Checkmate fan.

jrockway3• 7 years ago

I think if you focus too much on "$35" you will be very disappointed with the rpi. You need a power supply, that's $10. You need an SD card, that's $10. You need a case, that's $10. You need a micro HDMI to HDMI cable or two, that's $10. You need a fan, that's $10.

If you mentally decide "the Raspberry Pi is a $100 computer all-in" you will be much happier. You won't buy one to sit in a drawer (as many on HN have complained about), and you won't try to use a USB charger from your phone from 1992 and that SD card you got with your sandwich at IKEA and be disappointed that it's not very reliable.

jjwhitaker• 7 years ago

I have one in a drawr, like many. At my a few relatives I have PiHole running and they love it just had to walk my grandma through occasionally turning the pi off and on (pull the power, reconnect).

But I have the current Raspbian distro in a VM for messing around with as I don't need the hardware up. Once I have a use for the pi in my drawer it's going to be useful

henryfjordan• 7 years ago

but when the chip fails from heat stress, you only need to replace that. The case, cables, and power supply will all presumably be fine.

$100 upfront, $35 to replace

kingosticks7• 7 years ago

Despite the fact that doesn't add up, it depends what you are doing whether you need all that. I've had great value from my £34 Pi 4 since I don't need HDMI cables, cases or fans. I did also already have the other stuff too but I take your point there's no avoiding an SD card (yet).

microtonal• 7 years ago

It's a bit of a shame that what started out as an educational computer is about $100 to get started properly. Nowadays I recommend Micro:Bit for tinkering (our daughter has one, she likes it very much). It's about 20 Euro and you have everything needed (including a battery pack if you want to use it portably).

If you want a machine that fore serious work (NAS, media center, low-end desktop), before spending $100 one should at least consider spending a bit more and get a NUC. You can buy a NUC for around 120 Euro, then you have to add memory and storage. But at least, you get a machine with fast I/O, faster CPU, and is more expandable. It also does supports 4K and h.265 decoding like the Pi 4.

vectorEQ2• 7 years ago

most components should do fine under these temperatures no? on PC usually VRM's are heat sensitive, but the CPU can take pretty crazy temperatures itself.

is the issue similar on PI? What component is at risk at these temperatures? 60-70 seems a little hot for a small device , but is it really TOO hot?

Bootwizard3• 7 years ago

Damaging temperatures are generally between 90-100°C. Throttling can happen at lower temps and those are usually CPU dependent (and cooler dependent). Also CPUs with less cores handle thermal throttling worse as they have less cores to fallback on if one overheats.

kingosticks7• 7 years ago

It's very dependent on the device. Enterprise/networking-class chips I work with are usually rated for long-term reliability up to 125C, more recently that's come down a little bit (particularly regarding memories) but still significantly over 100C.

dboreham• 7 years ago

As a sometime hardware engineer, my rule of...er...thumb was that if it was difficult to keep your finger on the device for 5 seconds then it was overheating.

Damage to devices certainly doesn't happen at 100C but you might be talking about case temp under some assumptions about how that relates to junction temp for some specific setup. In general its junction temp that decides if the device suffers permanent damage.

husam212• 7 years ago

What about a bigger heatsink?

bjoli4• 7 years ago

That has been tried to great success with the rpi3, so I suspect it will at least make it less prone to throttling.

Edit: I just stacked a bunch of 10sec coins on the processor (without any thermal compound) brought the idle temperature down by 3 degrees C.

Edit2: Put an carbon tablet pipe on it, filled with coins. It is not up to heat yet, but right now it is idling at about 45C. It would probably be better with some fluid in it. I will probably keep this as my cooler.

Edit3: Seriously: I have wonderful thermal numbers. sysbench for 240 seconds, temperature 62C.

This is a rpi4 with a poe hat, so my passive cooling options are limited.

kekepepe• 7 years ago

What is 'carbon tablet pipe'? I tried to google it, but nothing useful turns up.

kees993• 7 years ago

Quote:

  the metal casing helps
  spread that heat around

It does, to a degree. But that is absolutely not what we are seeing in that IR picture. Shiny bare metal is a mirror at the wavelengths that thermal camera uses. So what you see on thermal image where wifi-module shield and CPU are is reflection of ambient (room) where this picture was taken. Try waving your hand around, you'll see it reflecting there too.

To measure real metal surface temperature by IR, you have to paint that metal (ideally, with black matte paint), or apply similarly-textured sticker.

gadgetoid3• 7 years ago

There's a better image here- https://medium.com/@ghalfacree/benchmarking-the-raspberry-pi...

nixgeek• 7 years ago

How was that accomplished? Extremely nice image!

book-mind• 7 years ago

That image is still highly misleading, you can see from the overlayed optical image that the CPU is not coated.

Ideally you'd want to coat any metal surface with black epoxy, and set the IR camera Emissivity Coefficient to 0.9 (the coefficient for black epoxy).

geerlingguy13• 7 years ago

True, I worded it a bit wrong. But the metal case is a huge improvement over the plastic die package on the Pi 3 B and earlier—a heat sink helps a little but you don't yet _need_ one if you use a fan, since the metal is much better at dispersing the heat.

kees993• 7 years ago

Indeed - there is enough aluminum/copper in the SoC's metal lid and PCB's inner (ground/power) layers, that the whole thing is effectively a 2-3 square-inch heat-sink. Eben himself has been talking about this technique around the time RPi3+ was released.

And your point here is completely understandable too - there is a kinda-heatsink there already. Just add a fan, and we're good.

My point is - seeing a large black hole where SoC goes (color corresponding to +20-ish degrees C by the chart) is utterly confusing, since SoC is the hottest point actually.

hinkley• 7 years ago

To what degree does scanning it in a cold room help?

JorgeGT3• 7 years ago

Yep, a lot of people nowadays is using IR cameras without any calibration or understanding of the physics behind the measurement. The truth is, the camera requires an emissivity coefficient to associate the received radiation with the emitter body temperature. There are tables for different types of materials, but the best is to calibrate against a surface thermocouple or similar.

A corollary of this is, when you see an IR picture of a product with very different surfaces like rubber, shiny metal, matte paint, plastic, glass, etc. you know that almost for sure the measurement is unreliable because at most they calibrated the camera for the emissivity coefficient of one of the surfaces. And they vary quite a lot...

DINKDINK• 7 years ago

people nowadays is using IR cameras without any calibration or understanding of the physics behind the measurement

The four factors are Emissivity (ε), Absorptivity (α), reflectivity (ρ) and transmissivity (t). Emissivity is only one facet. Ideal is high Emissivity and low reflectivity.

https://en.wikipedia.org/wiki/Radiation_properties

darkmighty2• 7 years ago

Indeed, but note it usually works well enough, because most surfaces have high IR emissivity (in particular with organics like plastics, papers, woods, fabrics, etc.; soils and liquids as well).

The one exception you have to be careful is with unpainted metal (high reflectivity). If polished it can be so low that even calibration doesn't help -- because you'd need extremely precise calibration that isn't practical and because reflections and noise/other heat sources will pollute you readings. In that case a simple sticker (or thermocouple reading) would be more adequate.

burnte• 7 years ago

He's measuring the temp of the board next to the CPU, not the shiny IHS on the CPU.

tagrun5• 7 years ago

Physicist here, and I disagree. Where else could that radiation with ~10 micron wavelength at that intensity with that localized spatial profile from that particular direction be coming from?

Yes environment typically will have some residual "noise" at those wavelengths, which you can check its intensity and spatial profile by taking a "dark frame" if you're in a strange environment and are really suspicious, but it's hardly going to alter what you're seeing in any qualitative way. Assuming someone isn't sending a focused beam of exactly that size at exactly that spot at an exactly correct angle at that particular wavelength.

klickverbot• 7 years ago

Physicist here too. What exactly do you disagree with? The parent comment is sound – thermal imaging cameras typically under-read on shiny metal surfaces. Their emissivity/absorptivity at relevant wavelengths is low, and reflectivity is high. Thus, their own Planck spectrum is (approximately) scaled down by their emissivity, and consequently the radiation in the measured MIR band is mostly what is reflected, which tends to come from the room-temperature environment.

A polished piece of metal makes a shitty black body. This is also why shiny metal (foil) is used to curb unwanted radiated heat transfer everywhere from thermos flasks and cryostats to space probes. (The lower emissivity further improves the efficiency of multi-layer insulation.)

jeffalyanak• 7 years ago

Understanding the reflectivity and emissivity of the material you are measuring is something that almost nobody accounts for outside of critical, professional applications.

Not that it makes the measurements in question any less inaccurate, but it's very common to see these problems in temperature measurements.

pankajdoharey2• 7 years ago

Check the Ice Tower cooler for raspberry pi https://youtu.be/RyUXC3886Ic

logicallee• 7 years ago

how about touching a thermometer to it? (granted that is one spot, but I'd think it's most precise of all.)

novaRom• 7 years ago

I cannot find a data sheet for its CPU (BCM2711B0). Is Pi4 actually an open hardware system?

tssva• 7 years ago

None of the Pi's have been open hardware systems.

strainer• 7 years ago

The Pi4 does not need a fan. There is a grand total of 10 watts of heat to dissipate, 15 watts max supply but that includes power sent to peripherals and wifi. A matchbox sized heatspreader which just touches each of the warm components will work assuming a bit of ventilation is arranged to let 40-50C air float away. The heatspreader shouldn't even benefit significantly from being a top conductive alloy - a bit of tin lid will do the job.

Experiences with shifting 200 watts for cpu cooling has people thinking dedicated alloy sinks and fins and fans are appropriate, but this is just 10 watts - it's child's play ;/

kemayo• 7 years ago

On a related note, there's a pending raspberry pi 4 firmware update which apparently makes a _big_ difference to how much heat it's generating:

https://www.pcgamer.com/amp/if-you-bought-a-raspberry-pi-4-g...

Last I saw, it's still causing some issues with performance of USB devices, which is why it's not in general release yet.

arendtio• 7 years ago

I think 'need' is a pretty strong word in this context. 'Could use' would be a better term, as the Pi 4 clearly works without a fan, just not at peak performance for more than a few minutes.

For many use-cases, I would prefer some performance reduction over the noise generated by a fan.

Marsymars• 7 years ago

Yes, if you're committed to a silent use-case, your options are essentially between a processor that doesn't throttle, or a processor that starts faster, and then eventually throttles to a steady-state matching the non-throttling processor in performance.

geerlingguy13• 7 years ago

Apparently a massive heat sink like the ICE tower (https://www.seeedstudio.com/ICE-Tower-CPU-Cooling-Fan-for-Ra...) can maintain a safe temp even without the fan running... but that also makes the Pi turn into a massive device with no chance of working in a standard case!

kingosticks7• 7 years ago

There's further information about the thermal control at https://www.raspberrypi.org/documentation/hardware/raspberry... which mentions that config option 'temp_soft_limit' can also be used. Interestingly it is not used by default on the Pi 4, but is set to 60C for the 3B+.

georgeecollins• 7 years ago

My problem is I use a shield on top of the PI for servo connections. I have found that a PI 3 can get hot without a case but with a board on top of it. I am glad they are improving the PI but I need to think about side mounted cooling.

ausjke• 7 years ago

I'm happy I have not bought the Pi4 yet, fanless for this kind of boards is the bottom line for me, if Pi4 needs a fan, then it crosses the line at least for me.

jsharf• 7 years ago

You needed to make that heatmap translucent and overlay it on top of the rpi with a diagram pointing to each chip and what it does. That would have been a super cool graphic.

pas2• 7 years ago

https://miro.medium.com/max/1838/1*KedwLPE9eXoeuwdciZpE0Q.pn...

MayeulC• 7 years ago

Reading all those IR images popping about the raspberry made me wonder why we're still using a "rainbow" (HSV) colormap.

I think there are better alternatives, that have both a linear luminance variation, and are colorblind-friendly:

https://news.ycombinator.com/item?id=17723041

stcredzero• 7 years ago

Raspberry Pi is becoming like a NUC. Meanwhile, there are people using Intel NUCs as fanless Hackintoshes:

https://www.youtube.com/watch?v=tUUP8K3RqAo

Fnoord• 7 years ago

Except the Raspberry Pi is an ARM SOC (ARM64 in this case), while Intel NUCs are x86-64. macOS requires x86-64 for now. If Apple ports it to ARM, I really doubt they'll make it easy to run on other ARM hardware.

opmac2• 7 years ago

They sell cases with heatsinks and fans for $10-$20. I would just recommend buying one of those versus modding one like the guy in the article did.

devinjflick2• 7 years ago

I feel like if I buy official parts, they shouldn't require modding to get the max performance out of the product. They should work without issue together. Currently you can barely get moderate performance with the official case.

This article and mod are helpful, even if obvious, for people like me who bought an official case with my RPi4 expecting them to work well together.

opmac2• 7 years ago

But they do work without issue, until you start stressing the CPU. In the majority of normal workloads, you don't run into thermal throttling, especially if not using the official case.

Also, if you have the official case and want to do this mod - for a few bucks more than the cost of two "pi fans" (which run $8 on Amazon), you can get a well designed case with heat sinks and a fan.

I see very little reason to actually do this mod versus buying a properly designed case besides the urge to tinker.

bjoli4• 7 years ago

So, I just stumbled upon an amazing heatsink while replying to a comment below. I use a painkiller carbon tablet pipe [0] that fits (barely) in my poe hat fan hole.

It brings the idle temperatures down to 42 degrees C, and sysbench never goes above 61 degrees.

Image here: https://imgur.com/a/Cr38Abz

[0] https://www.apotea.se/treo-brustablett-500-mg-50-mg-20-st

TazeTSchnitzel2• 7 years ago

If the Nintendo 64 was entirely passively cooled, surely the Pi can be? Mind Nintendo/SGI had much more surface area to work with so this is probably an unfair comparison.

bantunes• 7 years ago

The Pi 4 is much more powerful than an N64. So much so, it can emulate it in software.

seanhandley6• 7 years ago

Way to put it into perspective!

TazeTSchnitzel2• 7 years ago

Not in terms of heat output surely?

ChickeNES• 7 years ago

The Nintendo 64 has a U shaped piece of aluminum spanning the width of the console that screws through the RF shielding and into heatspreaders on the RDRAM, CPU, and RCP. It's about 2 RasPi's long by itself :P

RoutinePlayer• 7 years ago

Raspberry Pi 4 most definitely do need fan. I'm not sure why this is not being made more clear.

The default case for it also doesn't help dissipate the extra heat either :-(

I've ordered mine fans from pimoroni.com. I hope it addresses the issue.

TaylorAlexander• 7 years ago

The article references something called the “Flir” heatsink as a case, but maybe they meant this one by a company called “Flirc”?

https://flirc.tv/more/raspberry-pi-4-case

I didn’t find a raspberry pi case made by Flir, the thermal imager company.

pslam2• 7 years ago

This article is actually describing how the Raspberry Pi 4 does NOT need a fan.

This is not the 1990s. It is perfectly acceptable and even advantageous to design for a high peak:normal load ratio, with thermal throttling. In this case, it allows for a compact, cheap, fanless design for the vast majority of users.

There is no evidence the heat dissipated will impact lifespan. It is common for the components picked out in particular (power supply, USB-C controllers) to be deliberately designed to run hot. They aren't made on the same process as the SoC.

I feel like there is a missing piece of the software/hardware design art here. There are many takes like this on the Raspberry Pi 4 design. Why only one ethernet? Why no fan? Why not more USB-C? Because it's $35 and because, perhaps, you aren't the target majority market. It's going to satisfy the vast majority of people, and those it doesn't have very simple and cheap ways to mod it so it does.

ryanmercer• 7 years ago

To add to this, I wonder if a properly designed case could create a chimney effect (not unlike the crossdraft kiln Primitive Tech made in his most recent video) where escape heat is drawing in cooler air in such a fashion as to be adequate enough fo the vast majority of applications.

Not that fans need to be very loud, or even spin very fast for something of this size, I imagine relatively low RPMs (probably sub 100 RPM) could still achieve considerable cooling, especially with a crossdraft optimized case.

guelo• 7 years ago

But then you would need a "This Side Up ↑" label and you would only be able to orient the case in one way.

neetdeth• 7 years ago

See also: the Power Mac G4 Cube

geerlingguy13• 7 years ago

This is why I suggest in the video to just stick some ventilation holes in the top cover. Instead of the heat pooling in that area, it could escape, and there would be some natural convection—in through the gaps around the ports, out through the top. It wouldn't be as good as a fan, but definitely better than slapping a heat sink inside the case.

geerlingguy13• 7 years ago

I am not directly the target market, no. And the throttling itself is an indication that the heat was designed/accounted for in the Pi's design.

However, to say that the majority of users don't need better cooling, and it won't cause problems most of the time, seems inaccurate. If you use a microSD card to boot/run the Pi, how many of them are rated for blisteringly-hot operating conditions 24x7 (many people using the Pi as a computer will have it booted pretty much all day and just turn off the monitor, or go to screensaver).

And I have already had one PoE HAT's PoE socket pop partly off the board when removing it from a Pi 3 B+. Partly due to stress of flexing the board, definitely... but that kind of tiny solder joint on a part that is stressed when making a connection is exactly the point of failure that may not be directly caused by, but is definitely not helped by thermal stress.

codesushi42• 7 years ago

Fans fail too.

The heat dissipated will probably shorten the lifetime of the board. At $35 who cares though? And you have more to worry about from the SD storage.

The RPi needs an SSD. :)

unixhero2• 7 years ago

Just get an Intel NUC

amelius• 7 years ago

If you advertise a product with certain specs, and the user can only use the full capability during a fraction of the time, then that is misleading.

throw20102010• 7 years ago

It might be misleading, but it's not uncommon. Apple MacBook Pros have thermal throttled at high loads for the past several years. It has throttled for so long that reviewers were surprised that the latest version seems to be using a decent thermal paste and throttles much less.

So if Apple got away with it for years on computers that mostly sold for over $2k, then I think the RPi foundation will probably get away with it on a $35 board.

maigret• 7 years ago

Tell Tesla then, they cannot make a full fast lap of Nurburgring.

Actually, most cars can break so much so often before they lose performance because of overheating or even burning brakes.

BubRoss• 7 years ago

That's basically modern CPUs for the modern consumer. Laptops often have cooling that can't keep up, same with intel NUCs. Same even with ryzens with integrated video cards. There are bios setting for relaxed thermal throttling that let it get hotter that are a huge boost to performance.

cyanoacry• 7 years ago

There is no evidence the heat dissipated will impact lifespan.

I have to nitpick at this a little bit as a professional EE who works in high-reliability electronics. Wearout rates absolutely do depend on temperature (and thus heat), and thus the chips used here will have a shorter lifetime than those with active cooling. Now, whether that lifetime will be long enough for the common user is another question (maybe it's 1 million hours of life that get reduced to 100,000 hours, so not normally noticable).

pslam2• 7 years ago

Yes, wearout rate definitely depends on temperature, but without reference to any actual data, this is what I mean by "no evidence".

Is it reducing 10 year lifespan to 9 years? 9.99 years? 5 years? Was it 50 year lifespan? It's pointless conjecture.

morganvachon2• 7 years ago

I'll respectfully disagree. Running my Pi 4 with no fan/heatsink reduces performance to an absolute crawl. It's on par with the desktop on the original Pi released in 2012, i.e. nigh unusable for anything beyond saying "yep, it boots to desktop". Thermal throttling effectively neuters the device.

I have it in an open-air acrylic "sandwich" style case now, with the same Pi-Fan as the author, and it feels performant enough to use as a daily driver for web browsing and other light duties (basically on par with any Chromebook I've come across the past few years). It's still not "desktop replacement" level due to the SD card performance hit, but it's finally good enough for its intended use case in education without being frustrating. Once boot-from-USB3 arrives it will likely be fast enough to use as a second Linux workstation in a serious capacity.

Erlich_Bachman• 7 years ago

He said "no fan", why do you include "no heatsink" into that? Those are very different things to operate without.

floatingatoll• 7 years ago

The assumption implied here is that the Raspberry Pi should deliver continuous peak performance equal to its burst performance.

If the RPi4 specs indicated a peak performance of 10% of burst performance, adding a fan would be a material alteration of the published thermal envelope of the purchased RPi4.

Was this performance characteristic clearly indicated at time of sale?

If so, then the article title, and the assumption above, is wrong: RPi4 does not need a fan, as long as it adheres to the published burst and continuous specs. Clearly there’s room in the thermal envelope for improved continuous performance with a fan, but that in no way is a “need” if they are transparent about this spec.

If not, then they are in good company with Apple and other compact hardware manufacturers in failing to publish their thermal envelope burst/continuous details in clear specifics. If they comply enough to say “min speed / burst speed” then they comply with what modern users generally expect in marketing documentation.

Does the RPi community wish further detail to be included at time of sale regarding thermal envelope behavior and timings at room temperature using the passive cooling case provided? If so, that’s a fair request to make of RPi and one they can easily comply with.

rowanG077• 7 years ago

Did you actually try to run the Pi as a desktop replacement? That is what they are advertising. A desktop replacement that is useable for a couple of minutes and then throttles is not something you want.

pankajdoharey2• 7 years ago

I would prefer a noiseless option perhaps a good heatsink?

darkpuma5• 7 years ago

I'm sure this is a dumb question on account of how obvious it seems to me, but has anybody tried simply putting real heatsinks on this thing? Not putting it in an Al case or something milquetoast like that, but actually putting a proper finned heatsink/radiator directly on the SoC with a bit of thermal grease between them. Like you would do for a real PC, except without the fan.

AFAIK, the peak power draw of these boards is substantially less than 10 watts, so regardless of how high the temperature of one small part of it becomes, we're still talking about a rather small amount of heat energy that needs to be pulled off the board. My gut says that a passive heatsink with a relatively large surface area to facilitate radiation and convection currents should be able to do the trick.

ars• 7 years ago

The POE hat comes with a built in fan, so might be a nice option.

https://www.raspberrypi.org/products/poe-hat/

prashnts3• 7 years ago

I’ve been using old ssd cases (aluminium ones), which would otherwise end up in trash. Drill four holes, use a screw to create threads in those holes. Lay some thermal tape, and mount the pi. I haven’t seen it rise above 60degs — plus it looks alright in my opinion. Few pictures here [1].

I got rid of the ports because I don’t need them (headless) and so they mostly fit entirely. I’ll make some sorta cover though.

Edit: Forgot to mention that these cases are strong. It fell a few times and nothing visibly bad. I added Pimoroni shim in second iteration because I did want to keep hdmi there. Also left the Ethernet leds for indicator lights.

https://imgur.com/a/5DdWQ68

penagwin• 7 years ago

I have over 4 RPi's and many SSDs and I've never thought of that, nice!

pwg• 7 years ago

use a screw to create threads in those holes

You'll get better quality threads, and it will likely be easier, if you use a proper tap to create the threads: https://en.wikipedia.org/wiki/Tap_and_die

prashnts3• 7 years ago

Thanks for the pointer. I was mostly using discard material and accidentally discovered that screws can make threads (yeah, not a machinist) — otherwise I’d planned to use nuts on the other side. I might be able to find a tap at maker space nearby — I didn’t know what a “thread making tool” was called.

prashnts3• 7 years ago

Adding to that, these cases are an exact fit for three raspberry pi zeros, laid flat. I made a pHAT display board with it. Pictures:

https://imgur.com/a/bhnESTS

superkuh• 7 years ago

This is also true for any real computer which isn't a desktop or server. Smart phones, SBC, whatever, they all have form factors which mean they can't disipate heat easily. They all thermally throttle quickly.

Causality1• 7 years ago

FYI, you'll get much better definition from your Seek camera if you use orange-on-purple mode and adjust the focus. Here's a comparison picture I made of my ceiling fan: https://i.imgur.com/CjCFdlX.jpg

sm4rk0• 7 years ago

No mentions of PWM to regulate the fan speed according to the temp?

Duladian• 7 years ago

I picked up a 2G Pi 4 yesterday and did some basic thermal testing using the onboard thermal readouts.

None modified Pi 4 running the latest Raspbian will idle at 67C in a room that is 22C.

Pointing a small 30cm 5V fan powered off the GPIO header will reduce this to ~50C.

Placing a heatsink on both the CPU and RAM reduces the temp to 50C.

Modifying a Pi 3 heatsink + fan combo to fit the Pi 4 results in a 42C idle temp.

The life expectancy of the board may be decreased due to the higher idle temp. IMO I would say a heatsink is the bare minimum for running a Pi 4 and a heatsink fan combo is required for anything process intensive such as 4k video.

newsreview1• 7 years ago

The new Pi 4 looks amazing! It’s crazy to think the original only had a single-core processor, 256MB of RAM, and one USB slot.

ChuckMcM• 7 years ago

Apropos of the thread: https://www.seeedstudio.com/ICE-Tower-CPU-Cooling-Fan-for-Ra... (a fan for the CPU that is reminiscent of the first "big" Pentium fans). I asked on twitter if the RasPi had "jumped the shark" here, being sucked into territory it wasn't really designed for.

As someone who has lived through the microcomputer revolution it is amazing to see the "$100 desktop" at this point of history. If we arbitrarily pick 30 years as a delta (so 1989 vs 2019) and use BYTE[1] as a reference a 20MHz 80386 desktop with a 40MB hard drive was $2500 (as a clone, name brands were more).

An actually comparable computer (32 bit processor at 20MHz, 1MB RAM, 640x480 graphics, 40MB+ of storage (ignoring for the moment "protected mode") today can be built for less than $10.

That is a huge step function to try to absorb.

[1] https://archive.org/details/byte-magazine-1989-10/page/n347

omni• 7 years ago

The giant heatsink seems like plain overkill, given the author of the article was able to stop it from throttling under stress tests with a much smaller and simpler fan install

akira2501• 7 years ago

That is a huge step function to try to absorb.

It is a bit on the Heaviside, isn't it?

I'll show myself out.

Havoc• 7 years ago

My thinking has been more towards running with an oversized cooler.

e.g. I've got a tinkerboard which also tends to run hot & there simply adding a solid pound of copper did the trick.

Really not keen on having moving parts on my SBCs

sbhn• 7 years ago

The odroid xu3 had a fan. It was innoying i could here it at night.

megous• 7 years ago

I'd worry more about placement of the uSD card under the hottest parts of the board, where there's 0 air circulation in the original rpi case.

"The higher the temperature that the NAND flash experiences, the greater the acceleration of charge de-trapping mechanisms that could lead to random data bit failures. NAND endurance is also impacted since endurance has an inverse relationship to data retention, and the rate of wear-out of NAND cells is affected by temperature at the time of programming and erasing NAND."

https://www.eeweb.com/profile/eli-tiomkin/articles/industria...

This effect is very significant. It's like the acceleration being 250x higher between 25°C and 70°C.

galkk• 7 years ago

Might be anecdotal, but some cases with fan on Amazon went to "will be delivered after some date" in timeframe between morning and $CURRENT_TIME

mastazi• 7 years ago

In the pictures I can see only one hole immediately above the fan, but I assume you would need at least an intake and an exhaust? Where is the other one?

stevefan1999• 7 years ago

I'm always a fan for RPi4

bayesian_horse• 7 years ago

It already has plenty of fans, me being one of them.

paule89• 7 years ago

I would love to have a case for the Pi which can utilise a normal Desktop Tower Cooler. Be it 80, 120mm size coolers. The larger the cooler the quieter it can be. (Looking at some nice Noctua fans) Alternatively the seedstudio one looks good but how loud is it really? https://www.seeedstudio.com/ICE-Tower-CPU-Cooling-Fan-for-Ra...

travolter• 7 years ago

I was setting up some software on my pi4, just installing some packages with apt. Most of the time it was idling because I was away and not paying attention... and it indeed got very hot. Not uncomfortable to touch just yet, but this was really minimal load... Sounds like I'm getting a fan.

squarefoot• 7 years ago

Moving the CPU on the other side of the PCB would allow the use of a larger and more efficient heatsink, with no need for noisy fans, save maybe for heavy overclocking. Not to mention metal enclosures or panels which would easily become themselves heatsinks once the board is screwed on them using the right spacers and decent thermal paste. Noise aside, fans have moving parts which can break, especially cheap ones (just about all those used in consumer IT), and that makes them a weak spot; that's why I would avoid them whenever possible until really necessary.

w0mbat• 7 years ago

It would also be prudent to drill some air inlet holes in the case as far from the fan as possible to facilitate airflow. Otherwise you Have the fan sucking on a mostly closed box, which strains the fan and makes it hard to move much air through. The existing holes for ports seem inadequate for this as they look largely blocked.

g00s3_caLL_x2• 7 years ago

Well...I'm a fan!

Knyuck Knyuck

The Raspberry Pi 4 needs a fan

Related Stories