Modifying an HDMI dummy plug's EDID using a Raspberry Pi

https://www.downtowndougbrown.com/2025/06/modifying-an-hdmi-dummy-plugs-edid-using-a-raspberry-pi/

by zdw • 1 year ago

301 87 1 year ago

zdw• 1 year ago

You can also buy these with a passthrough, which is useful for older systems that balk at higher resolution monitors.

I have a 2011 era AMD FX8350 system where the onboard 880G northbridge+video chipset doesn't output video over HDMI correctly with a 4k display. Hooking up one of these inline to tell it to send a 1080p image works great, which the monitor does a 2x integer upscale to 4k.

dougg33• 1 year ago

I also have a couple of passthroughs -- I probably should have mentioned them in the post as another option. The one I have is fancy -- it can read the EDID from a monitor, save it, and use it as an override for another monitor.

Another awesome thing is it can force the monitor to always be detected. One of my monitors virtually unplugs itself when I shut it off, which causes a bunch of issues for me, and the passthrough completely solved it. The one I use is the HD-EWB by THWT.

gadiyar• 1 year ago

Doug, thanks for mentioning this. I didn’t realize pass-through ones existed. I’ll check out the one you have. Nice article btw.

avidiax2• 1 year ago

One caveat of these dummy plugs is that they don't do HDCP. They handle the typical use case of forcing a specific resolution output for headless machines rather well, but fail for the use case that you need to run something that expects HDCP.

This seems a good place to ask: does anyone know of a good solution like this HDMI dummy plug, but that negotiates HDCP? I need to test video streaming apps that require HDCP to play at full resolution, but it is inconvenient to have a full TV for every test.

The one solution I've found is an HDMI multiviewer, which seems to negotiate HDCP to each port individually.

mschuster91• 1 year ago

Try one of these HDMI splitters that are more or less openly advertised as "HDCP strippers" on Amazon.

crazysim• 1 year ago

I think multiviewer might have been a synonym for that.

I wonder if the chips on these dummy plugs are powerful enough to hack in HDCP support though.

dcan• 1 year ago

Terminating HDCP is difficult, you’d have to downgrade it to HDCP 1.4 and then have a 1.4 ‘compliant’ (see: device on the end for it to be a dummy monitor. If you need anything newer than HDCP 1.4, it’s likely not possible.

tverbeure3• 1 year ago

I did a tear down of this Monoprice dongle: https://tomverbeure.github.io/2023/11/26/Monoprice-Blackbird....

It terminates as an HDCP 2.0 endpoint and converts to HDCP 1.4. You’d still need an HDCP 1.4 sink to make it work though.

ndiddy2• 1 year ago

I use this HDMI splitter. It lets you either set a preprogrammed EDID, or learns an EDID from whatever you plug into HDMI output 1, and then shows up as a connected monitor for as long as the splitter's plugged in without having to connect anything to the outputs. I believe it negotiaties HDCP between the computer/console/whatever and the splitter, then sends the signal to the output monitor without HDCP. https://www.amazon.com/dp/B07VP37KMB

amelius• 1 year ago

I have a different usecase. I have an embedded system that sends out HDMI. However, its boot screen is something I want to replace by another HDMI stream (a static image would suffice). I specifically don't want to change anything on the embedded system for a thousand reasons I won't go into. How do I cheaply and robustly do this?

atoav• 1 year ago

Probably not the most elegant solution, but there are many HDMI switchers out there that can be talked to using gpio and/or RS-232. You could use one of those and a Raspi, feed the image in from the Raspi, detect the power of your embedded device via GPIO and then switch over to the other HDMI input. Whether that is a feasible solution mostly depends on other requirements, e.g. regarding power consumption or space.

I used a similar solution once in an AV context and it has been running reliably for years now.

If you want something less hacky Blackmagic has the Atem Mini, a good HDMI switcher that can also store multiple stills and can be switched via ethernet (among other things)

indrora• 1 year ago

https://www.ti.com/product/TMDS261B

This and an RP2040 to generate the second signal would probably work just fine; see https://learn.adafruit.com/picodvi-arduino-library-video-out... for an example of how to stretch the rp2040 to do HDMI

hedora• 1 year ago

Aliexpress sells things that claim to terminate hdcp and forward hdmi. Caveat emptor.

kachapopopow2• 1 year ago

I find it crazy that the signal between our monitors and desktop computers is encrypted when these exist.

bombcar• 1 year ago

There are others that end up doing the same thing - I believe some of the Decimators do - perhaps this?

https://www.decimator.com/Products/MiniConverters/12G-CROSS/...

dishsoap2• 1 year ago

Fun tip: the same process works to modify the edid stored on a typical monitor or laptop screen. Sometimes you can even change various settings on the tcon by writing to other i2c addresses. You also don't need a raspberry pi, any computer works.

crtasm• 1 year ago

The author recommends using a Pi while noting it's not a requirement

If you attempt these commands on a PC, it’s possible that you could accidentally flash hardware that isn’t an EDID, like a RAM module’s SPD EEPROM.

dishsoap2• 1 year ago

True, although the i2c controller that the dimms are connected to is an entirely separate device from the i2c controller in the gpu that's connected to the display ports. As long as you know what you're doing the risk is not significant.

ajb2• 1 year ago

The flash chip usually has a write enable/disable pin and most monitors and TVs will wire it to prevent writes to the EDID. I would guess only cheap ones don't bother. It's risky as without protection, a voltage glitch during a read can turn it into a write and trash the flash.

nyanpasu645• 1 year ago

Attaching the write-protect pin to +V is literally free in the PCB design process; IMO not doing so is a design error or decision (though IDK how much thought was placed into allowing users to rewrite the monitor identification).

Aurornis• 1 year ago

the same process works to modify the edid stored on a typical monitor

That would be a strange oversight by the hardware developers.

Typically they would buy pre-programmed EPPROMs and then place it on to a board where the write enable pin is never pulled high.

It would be strange to put an EEPROM into a product like a monitor and leave it writable, but I’ve seen stranger things on shipping hardware.

ajb2• 1 year ago

Yeah,it shouldn't happen - but I've seen it happen. What's worse, the first batch we got from that place weren't flashed with an EDID at all - and were shipped directly to customers (who mostly didn't notice, because the main product it connected to had default that worked, but it wasn't optimal. Meant none of those screens could be used with a normal laptop though). Ironically the combination of the two issues meant we could have fixed the EDID in the field, but we didn't dare in case we bricked someone's $x000 TV.

crote3• 1 year ago

Modern monitors don't even use an EEPROM chip for EDID anymore. The I2C bus is hooked up to a microcontroller inside the monitor, which allows it to implement Display Data Channel. This way you can tune things like display brightness and color profile from an application running on the computer, instead of messing around with the monitor's OSD.

Tools like ddcutil aren't very well-known, but they can be quite useful if you want to do something like DIYing a KVM switch by just having the PC tell the monitor to switch to a different input!

gblargg• 1 year ago

I did this once on an Acer monitor. I was modifying it to strobe the LED backlight to give blur-free video like a CRT. I had found that the DDC bus exposed other registers to control the backlight, etc. and had an external circuit connected to do the strobing. I noticed it had registers to read and write the flash ROM, so I dumped it, wrote an 8051 disassembler and did some crude reverse-engineering, then eventually modified the ROM to include a strobed mode (occupying the lower end of the brightness control, so it could enabled and adjusted via the OSD or normal DDC brightness controls). I did have to go inside and connect the write line when flashing it. There was conveniently an interrupt on vblank, and the timer that controlled the LED backlight had a mode that could turn it on a little before the next interrupt and then off an adjustable amount of time after, just the right time needed to flash it on after the LCD had settled updating. Originally I just wanted to remove the several-second boot logo (which I achieved).

awaymazdacx5• 1 year ago

hex dump for the USB ibus2 plug extract is concatenated to EDID

aappleby2• 1 year ago

Minor note for those wanting to try this at home - these cheap dummy plugs only have a 256 byte eeprom, which is not enough for storing the various extended EDID blocks needed to specify high-refresh high-resolution configs. If you just want 1080p60 they're fine, but you won't be able to simulate a 4k240 monitor with them.

Also, some of them have the write-protect line pulled high (or low? don't remember) and you'll need a bit of surgery to actually write to them.

klysm• 1 year ago

WP high vs low might depend on which chip is used.

01100011• 1 year ago

Does anyone know of a cheap DisplayPort EDID emulator to fix issues with a KVM and linux? Last time I checked, they were much more expensive than HDMI, to the point where it would be better to buy a new KVM.

crote3• 1 year ago

The issue here is that DisplayPort doesn't use a basic EEPROM hooked up to an I2C bus for EDID. Instead it uses the high-speed DisplayPort-specific AUX bus, which is significantly more complicated to mess around with. Heck, I don't think you can even find any decent documentation about it without joining VESA and signing a bunch of NDAs.

nyanpasu645• 1 year ago

You can override EDID in the kernel options (https://foosel.net/til/how-to-override-the-edid-data-of-a-mo...), but I don't know if you want to add a virtual monitor (unsure if https://askubuntu.com/questions/453109/add-fake-display-when... works).

mlukaszek• 1 year ago

Have a look at https://github.com/DisplayLink/evdi and (shameless plug, toy project, be gentle) https://github.com/mlukaszek/evdipp

slipheen2• 1 year ago

Relatedly, is there a good archive of EDID binaries somewhere, or a better program to make them?

I have an nice programmable EDID emulator plug, and I can clone my monitor and others, but there's some times there's a specific resolution or feature I want to set and I don't have a way to. (Like 8K with DSC, etc)

I'm aware of https://github.com/bsdhw/EDID but it's rather limited in terms of modern monitors.

I've also written by own using https://www.analogway.com/products/aw-edid-editor but getting all the nuances of various modes, and setting preference order, etc, is rather difficult, at least for me :)

3abiton• 1 year ago

I had a similar problem recently: I got this cheap 5.1 surround system soundbar that support up to Dolby TrueHD via HDMI. But here is the catch, it only works with eArc enabled devices (new gen TV). If you plug your PC you need to use SPIDF or aux which hamper the quality. One solution beside buying an audio ectractor/splitter is to fake the PC edid to be reconized as eARc by the soundbar. Still yet working on this, no strict guidelines existing unfortunately.

nyanpasu645• 1 year ago

I have (too much) experience in EDID editing. My suggestions:

- AW EDID Editor as you mentioned.

- CRU is a Windows-only tool, and will modify the EDID files it dumps from monitors (removing serial/etc. descriptors to make room for detailed resolutions), but will work. It does not run under Wine.

- 010 Hex Editor has an EDID template.

- On Linux you can install wxEDID from Flatpak (IIRC the distribution packages would crash in WxWidgets). I don't think it can create sections though.

- v4l-utils has edid-decode (which can be used as a git diff textconv tool), though this does not help you encode EDID files.

I found that HDMI EDIDs have a CEA extension block while DP EDIDs have a DisplayID extension block. I haven't done any work in multi-page EDIDs with over 256 bytes (and don't know what EEPROM chip you'd use to emulate them, nor the protocol or APIs to read and write them).

_kb• 1 year ago

https://www.extron.com/product/software/edidmanager30

https://www1.kramerav.com/au/product/edid%20designer

Both are free but not free to distribute. The Extron one may require you to be working on projects / orgs using their hardware.

The_SamminAter2• 1 year ago

What programmable EDID emulator plug do you use? I was recently looking into them, and it wasn’t clear what devices had what features, or if any (cheaper) ones were any good.

slipheen2• 1 year ago

https://www.store.level1techs.com/products/p/5megt2xqmlryafj...

ashirviskas• 1 year ago

Why are dummy plugs a thing? What can you do with them that you cannot do in software? (asking as a person who had no issues with having 18 virtual displays and no dummies).

dd_xplore• 1 year ago

I have a moded chromebox(booting windows and linux), which refuses to boot without any video device attached to hdmi port. So I had to use a dummy plug.

tshaddox• 1 year ago

Presumably it’s for devices which do not have easily modifiable software.

pfych2• 1 year ago

Dummy plugs are a lot easier for most people. I added a fake 4K monitor to my desktop via software for remote game streaming, and it was a lot more complicated than I expected[^1].

[^1]: https://pfy.ch/programming/4k-sunshine.html

lyu07282• 1 year ago

What gpu/driver were you using?

SXX• 1 year ago

A lot of OS / GPU / driver combinations dont actually let you setup virtual displays with arbitrary settings. And you might want it for setting streaming with OBS or games streamings via Steam / Parsec / etc.

Some years ago it's kind a worked for me on Linux with Xorg and open source drivers and Windows with Nvidia, but when it comes to MacOS or Windows+AMD or Intel GPU it simply doesn't work that well.

TheJoeMan• 1 year ago

Raspberry Pi’s with remote desktop won’t render the desktop unless a monitor is physically plugged in… easiest solution for say a PhD student.

ndiddy2• 1 year ago

One example: I use software called Looking Glass on my PC for interacting with a Windows virtual machine. I have two GPUs in my computer, an AMD one for the Linux host and an NVidia one that gets passed through to the Windows guest. Looking Glass then captures the NVidia GPU's output and displays it in a window on my desktop. This allows me to use Windows software in the VM and get acceptable performance (Windows has basically required graphics acceleration to run acceptably after 7). The problem is that the NVidia GPU will not do anything without having a display connected. NVidia Quadro GPUs support dumping a monitor's EDID and then mapping that file to an output (so the GPU always thinks that monitor is connected to that output), but their consumer-grade GPUs don't support this. That's where the dummy plug comes in.

leonheld• 1 year ago

We use it for testing binary embedded Linux distros where tricking the OS to think there's a display connected introduces a new variable that is not present in the user's deployment - and it's a cheap hardware solution. Buying and installing them is probably more cost-effective than having an engineer writing the `echo on > /sys/whatever` and the logic around it.

antgiant• 1 year ago

They make it super simple for someone on the move to do a zoom out teams call with one screen and still have access to PowerPoint’s presenter view.

Basically use the dummy plug screen for PowerPoint’s output and the laptop screen for the presenter notes. Then share the dummy plug’s screen.

Might not be the best answer for the citizens of Hacker News but so, so easy for teachers and salespeople.

TiredOfLife• 1 year ago

It seems that linux doesn't support virtual displays. On Windows you can either install a dummy display or have Apollo do it automatically. No such thing on linux.

detaro• 1 year ago

In addition to what's already been mentioned, I remember there being issues with macs not unlocking the full abilities of the GPU if there was no display present. Maybe there is some software workaround, but a HDMI dummy is cheap and quick and won't disable itself on updates etc.

RunSet• 1 year ago

What can you do with them that you cannot do in software?

It lets a macbook operate with the lid closed.

immibis2• 1 year ago

Convince a locked-down Fuck You Inc (I mean Apple) device to use a specific display resolution over VNC.

mrheosuper• 1 year ago

hdmi dummy plug is a hardware solution to solve a software problem that should not exist in first place at all.

HappMacDonald• 1 year ago

This sounds like a description of a huge number of extant hardware solutions, to me.

1vuio0pswjnm7• 1 year ago

Can dummy plugs be used to change device fingerprinting

Simon_O_Rourke• 1 year ago

I don't get it - why do you need to spoof having a monitor connected for a Raspberry Pi? Surely they boot up fine regardless?

Gigachad• 1 year ago

Did you read the article? The RPI is just being used to reprogram the dummy plug.

cdg007• 1 year ago

been eyeing this kind of solution

m000• 1 year ago

I'm confused. I was expecting to see th plug hooked to the GPIO i2c pins, but just plugging it to the RPi appears to be enough. So, does HDMI directly expose an i2c interface?

pm215• 1 year ago

Yep -- the DDC link which is the comms part of VGA/HDMI/DVI is basically an i2c link, and that's how the OS queries the EDID in normal operation.

As the article notes, the rpi has an i2c controller wired up to those hdmi port pins, because it needs to be able to read the EDID over the DDC.

Modifying an HDMI dummy plug's EDID using a Raspberry Pi

Related Stories