Giant 'sand battery' holds a week's heat for a whole town

https://newatlas.com/energy/sand-battery-finland/

by aa_is_op • 2 years ago

289 178 2 years ago

newatlas.com

xnx• 2 years ago

Large-scale ‘sand battery’ goes online in Finland

https://news.ycombinator.com/item?id=32006791

2 years ago | 287 comments

A sand battery could transform clean energy

https://news.ycombinator.com/item?id=33465272

1 year ago | 143 comments

gorpy72• 2 years ago

This is great technology, simple and effective. I’ve spent many hours reverse engineering to see how effective and expensive it might be. I’ve found it’s very cost effective but heat can be hard to calculate. i like that they did a prototype. i think i’ll do one at some point. for an individual house it makes more sense to improve my insulation but i think ill still build a small version for fun.

dragontamer8• 2 years ago

IceBear went out of business with the opposite tech: tanks of water storing the cold generated from excess AC cycles.

Cheap electricity can make cold, and then a fan can convert the cold water into cold air during peak hours when electricity was costlier.

Fans still took electricity to run, but it'd only be a few hundred watts to run air-conditioning rather than kilowatts of power.

0cf8612b2e1e• 2 years ago

How long ago was this? The idea seems simple enough and would really benefit from the increasing glut of renewables. Even better, unlike a sand battery, you can potentially cycle it for several months of summer, by offsetting consumption by just a few hours feels like it could be economically viable.

Then again, the competition is general purpose batteries which can be used all year and probably require less maintenance.

abkfenris• 2 years ago

My local power company worked with a bunch of businesses in my town to install these rather than upgrade the dead end line for a few peak periods.

ZeroGravitas• 2 years ago

IceBear was competing directly with ever cheaper PV.

It's a tech for time shifting cheap overnight energy to the expensive daytime.

Installing PV gives you cheap power directly and correlates with air-con demand.

logtempo2• 2 years ago

it's how "rocket stove" works: https://en.wikipedia.org/wiki/Rocket_stove

Since you burn the wood really fast, you need to delay that heat release. That's where sand comes in as a cheap and good enough material. There are also systems that heat water and store it in a tank, which also make sense if you want hot water in your house too.

zdragnar• 2 years ago

Sand is actually pretty bad. Gravel is a little better, clay is best.

Sand is really only useful here because that much clay is usually significantly more expensive and would take forever to dry out.

Source: researched the shit out of and have built a rocket stove.

photonbucket• 2 years ago

I'm curious about "why sand", is it better at holding heat than say water?

dragontamer8• 2 years ago

Probably not.

But sand doesn't freeze (or perhaps, sand doesn't melt) under normal temperatures. That's probably more important for an icy region.

tonyarkles3• 2 years ago

Probably not relevant to the specific problem at hand because sand that's getting heated to 600 degrees is going to quickly boil off any residual moisture. As a warning, though, so that people don't experience the pain I got to experience, a pile of sand is really good at holding onto water internally and freezing when it gets cold. We had to replace our sewer line a while back and for various reasons were taking care of filling the hole and redoing the concrete ourselves. The sand guys left a big pile in the driveway for us and as soon as winter came the whole pile turned into a single giant rock despite having been out in the hot sun previously.

Exactly to your point, though, one of the great things about using sand for this application instead of water is that you can probably just shut the thing off for maintenance without having to worry about draining all of the sand out. If it freezes up due a bit of residual moisture content it's not going to expand nearly the same way that a silo full of water would, and it should be easy enough to thaw out just by putting some heat into it.

Waterluvian• 2 years ago

It’s probably less likely to turn into gas, increase in pressure, and explode the silo.

christkv2• 2 years ago

Can store a lot more heat by volume. Water has other bad properties. The higher the temperature the higher the pressure.

Terr_• 2 years ago

[Sand] Can store a lot more heat by volume.

A quick caveat/clarification: It's only true if you're pushing the system over the 100°C mark. Otherwise a volume of liquid water--with its greater latent heat-capacity--will outclass the same volume of sand.

Water's heat-capacity is 4.186 J/g°C, while estimates for sand run towards ~0.830 J/g°C. If we also assume the sand is 1.6x denser, then our below-boiling water still comes out ahead at ~3.15x the joules per volume.

There are hints [0] this system tops out around 600°C.

[0] https://polarnightenergy.fi/sand-battery

SuperNinKenDo• 2 years ago

In addition to what others have said, isn't one of the weird properties of water that it tends to take in energy easily, but not give it back so easily? I've never really understood how that works, but I think I've leqrned that at some stage. Hence why it's used in cooling so much. Somebody jump in and tell me how wrong I am, or if I'm on a track that doesn't lead completely nowhere.

candiodari• 2 years ago

Water vaporizes, and at that point blows up just about every container you can build around it. As will ice when it cools down. Sand is just sand, very little difference, very unreactive from way under freezing temps to about 1300 degrees.

And you might vent steam, but you should probably take into account that while water < 45 degrees or so is pretty innocent, steam will strip flesh from bone starting at 180 degrees or so, it won't "just" burn you.

mrspuratic• 2 years ago

maybe this? https://en.wikipedia.org/wiki/Mpemba_effect Or, more generally: "Heating and cooling are fundamentally asymmetric and evolve along distinct pathways" https://www.nature.com/articles/s41567-023-02269-z

pfdietz3• 2 years ago

Sand is cheap, and stays stable up to 1200 C or so. For conversion back to work the efficiency will be much higher than for lower temperature water.

ben_bai2• 2 years ago

It's more effective volume wise. I did the math, some time ago here are the rough numbers.

Sand has way less heat capacity then water per kg (about half).

Water can be heated to 95C with standard unpressurized vessel. Sand in this application is heated to 600C.

Sand is denser then water (kg/m3).

For the same heat energy stored this comes out to about 2.5x more volume of water(95C) compared to sand(600C).

Water and Sand are both dirt-cheap.

Hot water can be managed with standard plumbing equipment.

Sand needs some high temperature piping (hot air to water heat-exchanger, resistive heat tho heat up the sand).

How well both contain the heat is primarily dependent on the isolation. Which favors the smaller footprint of sand, but needs to isolate a higher temperature difference...

tjmc• 2 years ago

One advantage of heating water over sand is that you can heat it up with high temperature heat pumps which currently have CoPs ranging between 2.4 to 5.8 [1]. So for every kW of electrical energy you put in you get at least 2.4kW of thermal energy out.

So yes, the volume of 95C water would be much greater than that of 600C sand, but if volume wasn't an issue you could do it much more efficiently. Alternatively, you could use battery storage for just the electrical capacity required and not the (much higher) thermal capacity which may be more cost effective when you look at the conversion.

[1] https://www.sciencedirect.com/science/article/abs/pii/S03605...

shellfishgene• 2 years ago

The temperature also matters. If you need at least 50 C water to run district heating, about half of the energy stored in near boiling water cannot be utilized. This is much less with 600 C sand.

fghorow• 2 years ago

No advective heat transport in sand. In tanks of water, on the other hand...

That means that the hot middle of a sand pile stays hot, instead of advecting to the outside, where it cools by conduction.

Ekaros4• 2 years ago

Note here is also that district heating uses water that is heated to 65-115C.

Which means that you have rather little of delta to work with. And at upper end it becomes somewhat risky to have large container of water that is beyond boiling in normal pressure...

With sand you can use very simple heat-exchangers. No need to use exotic heat pumps that require extra energy...

Karellen• 2 years ago

Something similar, but more for industrial processes: Can a Simple Brick Be the Next Great Battery? | John O'Donnell | TED

https://www.youtube.com/watch?v=X6Wgd4v_yW8

fy20• 2 years ago

This is basically how houses in central Europe work. The walls and floors are built with masonry (bricks or concrete) and wrapped in a thick layer of insulation. This results in a building with a very high thermal mass.

The result is that it takes a long time for the inside of the building to change temperature.

The other day we had a warm sunny spring day (5C / 40F), so I opened all the windows and did some spring cleaning. I set the thermostat to 16C as I didn't want the heating coming on while I was doing this.

I forgot about this, and the next day when I woke up wondered why the temperature in the house was only 20.5C (68F) as usually we have it set to 22C (72F) - then I remembered I effectively turned off the heating 18 hours ago, and forgot to turn it back on.

tamimio• 2 years ago

It isn’t a totally new concept, in CSP (concentrated solar power) plants, a molten salt is used to store the heat as well.

yeknoda• 2 years ago

novelty is secondary to implementation

defrost4• 2 years ago

CSP Pilot plant broke ground 12 years ago:

    In 2012 Vast Solar commenced its 1.2 MW Performance Validation Project which was supported by funding from the then Australian Solar Institute.

    This CST project was completed on 22 October 2019.

https://arena.gov.au/projects/csp-pilot-plant/

Scaled up second stage is being built out now (2024):

    Vast said on Friday that it has partnered up with global design and manufacturing firm Contratos y Diseños Industriales (CYD) to take the next step forward on its VS1 project, the 30MW/288MWh plant in South Australia.

(Aug 2023): https://reneweconomy.com.au/australias-biggest-solar-thermal...

Qwertious2• 2 years ago

It isn't totally new, nothing under the sun etc etc, but honestly it's closer to a hot water tank than it is to CSP. Which makes sense, since the original conception of PNE was a hot water tank IIRC.

CSP stores heat as a means to produce electricity, the PNE sand battery stores heat as a means to provide heat. CSP's molten salt was heated by pumping it through (solar) heated pipes, which meant it had to have the correct fluid properties etc. The PNE sand is heated in-place via electricity which means it can be basically any old crap, as long as it's inert at 600 degrees or less.

In other words, CSP differs drastically by the energy input method, the energy output method, and the composition and requirements of the storage medium.

Basically all of the PNE tech is centuries old, the point is that together in this specific configuration they're an incredibly cheap heat storage medium - resistive heating, insulation, sand, all cheap.

100k• 2 years ago

There's some interesting companies in this space.

https://gofourth.com/ - focusing on grid storage, uses graphite (carbon) and liquid tin for heat transfer

https://antoraenergy.com/ - industrial heat and electricity

https://rondo.com/ - industrial heat

You can find interviews with their founders on the Volts podcast.

pfdietz3• 2 years ago

NREL's ENDURING sand battery, storing heat at 1200 C in quartz sand. Round trip efficiency using turbines is estimated at ~53%.

https://arpa-e.energy.gov/sites/default/files/2021-03/07%20D...

The IP has been licensed by Babcock and Wilcox, who are the source of the nifty compact fluidized bed heat exchanger.

chiph• 2 years ago

It's an interesting concept. Cheap. Doesn't take up a lot of space. Could be driven by a solar furnace.

My concern is whether the cyclone particle separator will do a good enough job - gas turbine blades don't like being blasted with grit. I expect they'd need a heat exchanger to be sure to get only clean gas driving the turbines.

pfdietz3• 2 years ago

Could be driven by a solar furnace.

Perhaps more interestingly, it could be driven by combustion of an e-fuel as a backup in case the sand becomes depleted.

hanniabu• 2 years ago

Cheap.

Until patents are involved

Animats• 2 years ago

This new sand battery is expected to stand 13 m (42.7 ft) tall and 15 m (49.2 ft) wide, providing an output power of 1 MW and a capacity of 100 MWh.

That's impressive. It's close to the energy density of fuel oil. Or did I calculate that wrong?

noqc4• 2 years ago

100 MWh is 8 tons of "oil", according to a google search. Oil is probably about the density of water, so 1 cubic meter is about 1 ton of oil, and this structure is about 2000 cubic meters, so oil has 200 times the fuel density of this battery.

It's still pretty good though.

reaperman• 2 years ago

“Oil” is 10-15% less dense than water. So yes, “about” the density of water, for napkin purposes. This would be diesel or heating oil.

Gasoline is 30% less dense than water though.

logtempo2• 2 years ago

your number is good, as it's the heavier from all oil. Don't work for all type of oil though.

https://en.wikipedia.org/wiki/API_gravity

    Light crude oil has an API gravity higher than 31.1° (i.e., less than 870 kg/m3)
    Medium oil has an API gravity between 22.3 and 31.1° (i.e., 870 to 920 kg/m3)
    Heavy crude oil has an API gravity below 22.3° (i.e., 920 to 1000 kg/m3)
    Extra heavy oil has an API gravity below 10.0° (i.e., greater than 1000 kg/m3)

bicebird• 2 years ago

I was thinking of ways to get around the peak solar generation being when you don't need it for heating and genuinely really heartening to hear about solutions like this.

The article doesn't mention the costs or complexity in building each unit but definitely implies it's cheaper than storing it batteries, which makes sense if it's essentially a heating element buried in sand.

Wonder what the smallest viable size would be, could you have one for each street / block of flats? One of the comments mentions burying them for better insulation which I'm assuming they didn't want to do just for the prototypes?

llm_trw4• 2 years ago

The article doesn't mention the costs or complexity in building each unit but definitely implies it's cheaper than storing it batteries, which makes sense if it's essentially a heating element buried in sand.

Batteries are more expensive than nuclear power so yes, anything else is better.

The issue is that we can't both electrify everything and use legacy heating applications. Going back the the 20th century idea of central heating/cooling is great until you realize the costs involved with adding all the plumbing to buildings which were never designed with it in mind.

noqc4• 2 years ago

Peak solar is peak A/C usage in the summer, which is typically more expensive than heating. In colder times more energy is used at night, but I think less energy is still used at night in the winter than in the day in summer.

fbdab103• 2 years ago

That does not seem right.

A hot day in summer might be 35C->20C (95F->68F). Winter is going to be more like -10C->20C (15F->68F) twice the temperature gradient to overcome.

Newlaptop• 2 years ago

Using the term "energy" here is suboptimal because it's mixing grid electricity with gas power.

A/C tends to be powered from electrical grid. Heat is often from propane or fracked gas.

More energy overall is used to heat homes in cold climates, but cooling homes in hot climates creates the challenging grid demand.

ionwake• 2 years ago

Sorry to a noob can someone explain this please. They are just heating up sand right?

loeg• 2 years ago

Yep.

Ekaros4• 2 years ago

Yep, combined with district heating that works with simple heat exchangers, it is pretty decent system. So you either pump power to sand or take heat from it and put it heating network.

gorpy72• 2 years ago

Ben_bai said it pretty well. water is good but it can cause rust, pressure, freeze, leak, etc. sand avoids most of this. the big thing is that sand can be heated much much hotter and this helps make up for its shortcomings relative to water. they likely charge and discharge with air blowing thru stainless steel network of pipes thru the sand. this would require special tuning. as someone else mentioned, the thing with water is that the temp is uniform everywhere because water transfers heat within its volume easily. sand doesn’t, so you need pipes spaced out right. i’ve wondered about insulation but, i think you can step it out with refractory bricks first then a mineral insulation, then something like perlite or fiberglass. the hot air would interface with heat exchanger to transfer the heat to whichever fluid that would go on to heat the home/s. since the sand can be heated to 1700F or more, a kiln or quartz heating element that can exceed this temp is needed. last, a thermally isolated heat temp tolerance fan would be required. i guess a slew of sensors in the sand and at the exchanger unit and output, i can imagine wanting sensors everywhere for tuning sake.

Valgrim• 2 years ago

Some Youtube folks tried a much simpler approach:

Take a large metal bucket or barrel.

Put a heating element and a simple oven thermostat on the bottom.

Fill with sand.

Connect to a solar panel or other enrgy source.

The air between the sand particles seem to actually provide a bit of convection and insulation.

The thermostat turns the circuit off before getting too hot for the heating element.

The heat accumulated during the day is slowly released over time directly through the metal.

immibis• 2 years ago

Any system that involves an electrical solar panel connected to a low-temperature electrical heater is likely to be better served with a solar hot water panel, by about a 10:1 ratio.

Dalewyn• 2 years ago

For some reason this description sounds exactly like a computer, and specifically the CPU/GPU, and I love it.

kiney• 2 years ago

Thats just a regular storage heater...

rkangel• 2 years ago

This is called a Storage heater (https://en.wikipedia.org/wiki/Storage_heater), usually referred to in the UK as a Night Storage Heater as it took advantage of cheap electricity at night to provide heat for a house.

Fitting Night Storage radiators was a much cheaper way of fitting central heating than the normal boiler and plumbing approach, and when electricity was cheaper it made more sense. Now, it makes no sense and if you buy a house with it the first thing you have to do is put in "proper" central heating. But maybe with excess renewables that will swing back.

prometheus762• 2 years ago

I'm toying with the idea of building one of these to use as a pool heater. Has anyone here tried this?

lancewiggs• 2 years ago

MGA Thermal uses tiny aluminium droplets in carbon matrix material to do heat storage with 1: constant temperature storage and 2: at much higher temperatures and energy density that allows for steam generation etc.

anonu• 2 years ago

It feels that Europe is so far ahead the US in matters of environmental sustainability. Why is that? Is it more dense than the US, so they need to be more careful with resources?

Gigachad• 2 years ago

Less politically radicalised maybe? America should have all the tech and resources required to pull this stuff off, but it just doesn’t happen.

yurishimo• 2 years ago

It's mostly centered around cost. Fuel (of all types) is so cheap in the US that efficiency was not an ultra high priority for most people. Ironically, the US has now gotten extremely competent at drilling for natural gas and the price is going to stay pretty much fixed where it is for the next 50+ years. Most of the waste from the early days has also been reduced and funneled into new petrochemical production processes that used to be reliant on oil.

If you are going to stay in one place for a long time, renewable solutions to problems like hot water and residential electricity are worth the investment, but with the migratory nature of the US worker, it's often cheaper for a household to pay for fuel for 5~ years rather than invest in a renewable solution that they will never reap the monetary benefits from.

From what I've experienced since moving from the US to Europe in 2022, it's a lot more common for people to stay in the same houses for an extended period of time. Especially here where I live in the Netherlands, you can commute to work almost anywhere in the country in about 2 hours by car. This allows people to keep the family home.

gregwebs• 2 years ago

Much of the US has access to cheap natural gas. And a good amount of oil. The greater the cost of energy the more it drives innovation in energy usage as well as incentivizes projects that would have a longer pay back period where energy is cheaper. Although Norway has abundant energy but socialized the profits and is using them to advance their usage of renewables and electrification. In the US we privatize the gains and only socialize the losses.

komali22• 2 years ago

Europe is more politically progressive (in some ways) than the USA, and sustainability is a progressive standpoint. Political identity politics in the USA means that even if you have a ranch in rural Texas and are directly observing the negative effects of fracking on your local environment, you still support the people that are trying to make more of that happen because if you don't, well, you must hate pickup trucks and beer and Christians too (drawing on personal experience as a Texan).

I've poked around on this topic here and there when bored and never found many good explanations for why this is the case. Probably a million weird little reasons, historical, economic, cultural. IMO the country is just too damn big to try to claim a single cultural identity, and it's resulted in absurd caricatures of polarized political identity, fostered as well by a two party system where it's basically impossible to be represented well per your values. In the USA you can't vote for someone that's promoting reducing government spending without also voting for someone that's attacking trans people's right to exist, or at least in the same party as such a person. Or someone that's trying to take away your wife's healthcare rights. Same way you can't vote for reducing oil dependence without also voting for, idk, taking everyone's guns away.

hnaccount_rng• 2 years ago

It's also that the infrastructure of the US is very young. In Europe a 100 year old building is shockingly common. And they are still in use. Mostly because even back then (some) housing was already build in a lasting manner. And not being able/willing to tear them down gives you a baselevel of sustainability.

The other thing is that we used up most of "our" fossil energy reserves decades ago and what we want to burn today requires imports, which requires a reasonably stable world economy, a reasonably strong geopolitical position and ... well ... even the last conservative governments have woken up, that those assumptions may not be true any longer

progfix• 2 years ago

Civil engineering in general is more advanced in Europe. The oil crisis in the 1970 and the subsequent use of thermal insulation made "Bauphysik" (building physics) an integral part of the planing process. In the US you just rely on more heating/cooling power instead.

Just as an example: >=16cm thermal insulation + heat pump or solar thermal energy + double or triple pane windows have been standard for new single family homes since at least 2005 in Austria.

chmod775• 2 years ago

Reminds me of Berlin's water heat storage tank: https://www.energy-storage.news/vattenfall-starts-filling-up...

It's specifically intended to store surplus energy from renewables for later use.

heyalexej• 2 years ago

Here's a smaller scale water battery that heats an entire house year round. The water tank itself is placed in the center of the house across all 3 floors and actually makes for a quite nice design element as well. The energy is generated in the warm seasons and the volume of water is large enough to last through the entire winter. It's a German vid but subtitles are quite accurate.

https://www.youtube.com/watch?v=MBLiNHsod8Y

WithinReason• 2 years ago

You don't even need water, you can just transfer the heat to the soil under your house

AnthonyMouse2• 2 years ago

Doesn't this suffer the problem that you're then putting heat into the device, which is in your house, during the warm season when you want your house to stay cool?

defrost4• 2 years ago

Think of the water tank as being in but insulated from the house.

In the hot summer the hot air within the house is cooled by heat pumping the heat into the water tank which is slowly over weeks bought up from cold to mean summer tempreture.

In the winter the heat is extracted from the water and transfered to the house.

The house and the water mass are out of phase by six months.

mythhabit• 2 years ago

It's a large enough volume of water, that adding insulation is feasible.

romafirst3• 2 years ago

This is super cool

at_a_remove• 2 years ago

I've been obsessed, mildly, with Feolite. It could be brought back for these sorts of applications to great effect. It's got the volumetric heat capacity of water and the ability to withstand much greater temperatures without any annoying phase transitions. It was very popular in the UK, where they went in early on charging for electricity on a rate varying by hour. The basic formula is easy, but there's a lot of secret ingredients to get the heat capacity way, way up.

Speaking of home uses and phase transitions, they have made inroads into making materials with a phase transitioned tuned to household temperatures. Say you have aimed for seventy-two Fahrenheit. The temperature gets higher than that? The material melts, absorbing ambient heat. Then, as the temperature dips below seventy-two Fahrenheit, it freezes, releasing heat. It would make a fantastic sort of "heat capacitor," designed to deal with rapid, small-scale temperature fluctuations, while larger heat batteries could deal with fluctuations over days, weeks, and so on.

Only problem is that these phase transition materials tend to be terrifyingly flammable, so far. Like soaking all of your drywall panels in candle wax before putting them up.

turtlebits• 2 years ago

You can DIY this on the cheap by connecting solar panels directly a $10 hot water heating element and burying it in sand. You will need to pair the right spec element with your panels

No charge controller, inverter or battery needed.

scotty79• 2 years ago

Heating element from pyrolytic oven would be better.

m463• 2 years ago

I get that sand is inexpensive and simple and I like the idea - especially since it scales to an entire town (!)

But I can't help but think of one "technology" that could make a scheme like this MUCH more effective.

a phase change.

for example, it takes 1 calorie for water to go from 30 to 31 degrees F, but but it take 80 calories to go from solid at 32 to liquid at 32 F.

A project I remember reading about that was really interesting was a house constructed with logs that had a resin that phase changed around room temperature. The idea was that the logs would be heated by sunlight, and the resin in the logs would absorb lots of energy without easily going above room temperature. Then at night, they would slowly solidify and give off heat at room temperature. This would be a cool way to stabilize house temperatures without needing equipment.

EDIT: it was called the enertia house

I'm uncertain of the history, it seems there are a lot of different "enertia house" search hits.

Here's one explaining the idea:

https://enertia.net/howitworks.html

jessriedel• 2 years ago

There's a pretty cool coffee mug based off the idea too

https://joeveo.com/pages/the-temperfect-mug

ImPostingOnHN• 2 years ago

Coffee Joulies work off the same concept

https://www.baristamagazine.com/coffee-joulies-engineered-so...

londons_explore2• 2 years ago

Dunno what 'wax like substance' they use, but if I were designing it I would use sodium acetate (vinegar+baking soda).

By adjusting the amount of water in the mixture, you can fine-tune the phase change temperature to whatever the customers like for their coffee.

It also boils above 100C so when the customer puts it in the microwave it won't burst unless they boil the cup dry.

And when the customer does break it, it's non toxic and food safe.

sudhirj• 2 years ago

Phase changes will probably work well for structures that would otherwise be used for insulation anyway - in the case of this particular idea though, I think heat is moved in and out using another medium, air in this case, so a phase change would complicate things greatly (hard to bubble air through lava). But yeah, something like a phase changing fluid (gas <-> liquid) will probably work well, as it does in air conditioners right now.

usrusr• 2 years ago

Phase change heat storage is well established techology. It's in the product you buy when you want to have building scale latent heat storage. I've even seen a company trying their luck at the business model of selling heat in twenty foot equivalents, e.g. for building sites. So it's safe to assume that they knew about this option. But there's also the square-cube-law, at some point it will be cheaper to insulate a larger volume of the cheaper material than a smaller volume of a material that requires less volume per unit of energy at the heat range you aim at. It's well possible that this line is between building-scale and grid-scale storage.

foofie• 2 years ago

But I can't help but think of one "technology" that could make a scheme like this MUCH more effective.

I think this is one of those things that drive home the point that there are fundamental differences between physics and engineering.

The article states that the thermal silos are heated with excess energy from the power grid. This alone tells you right from the start that efficiency is not the primary requirement.

Sand is inert, doesn't decompose or degrade, is readily available, is easy to work with, and has no moving parts. You can make it work in a silo, or digging a well to fill it with sand. In fact, geothermal heat pumps are already used extensively in residential buildings to regulate temperature. You just have to drill a hole in the ground that's deep enough, run a water pipe through it to heat/cool the water, and run that water through your building to heat/cool the environment. The nifty trick of Polar Night Energy is that they introduce the extra step of actively heating the thermal source with cheap energy supplied by the electrical power grid.

This sort of argument is like complaining that a Formula 1 car is far more efficient than a Volkswagen Golf. Yes it is,but that's a mute point.

standardUser• 2 years ago

I can't endorse this perspective enough. The amount of energy storage we need is staggering and ever-growing. We've someone convinced ourselves that the 'baseline' is consuming with abandon millennia worth of stored energy and anything even slightly less responsive than that is too inconvenient. Given those parameters, we need any and all energy storage options and efficiency is not a priority. Tesla powerwalls were never going to power the world, but giant caverns full of sand might.

btbuildem• 2 years ago

Excess energy from the power grid -- in times when renewables produce excess energy.

Otherwise, the heat to be stored comes as a byproduct of local industry. Something that would otherwise be vented out and not used.

freddie_mercury• 2 years ago

I get that sand is inexpensive

It depends where you are. Sand thieves are a thing in many places around the world.

Here's a story from 2015 about how residents in one area have lost 25 hectares of land to sand thieves.

https://tuoitrenews.vn/news/features/20150524/residents-losi...

Or a police captain whose legs were severed while trying to apprehend sand thieves.

https://www.vietnam.vn/en/dien-bien-moi-vu-dai-uy-cong-an-bi...

And here's a longer from article on the phenomenon:

https://www.mekongeye.com/2023/05/01/mekong-delta-sand-minin...

tl;dr sand is used in construction

nasmorn• 2 years ago

It is still inexpensive, they just steal a lot

yetihehe• 2 years ago

For construction you need a special kind of sand (still pretty common on average). For this battery you can use sand unusable for construction.

kumarvvr• 2 years ago

Sand used for construction should not have salt content.

For energy storage, any sand is sufficient.

kwhitefoot• 2 years ago

The article points out that it doesn't actually use what people usually think of as sand:

"The sand itself will also be sustainably sourced – it’ll consist of crushed soapstone, which is a manufacturing byproduct of another local industry."

jillesvangurp• 2 years ago

The sand itself will also be sustainably sourced – it’ll consist of crushed soapstone, which is a manufacturing byproduct of another local industry.

The requirement is not really construction grade sand but any substance with a largish thermal mass. Sand/dirt/crushed rock, etc. whatever you have right on your doorstep. There have been plenty of prototypes using such various materials as thermal mass.

All you need is a big container, some insulation to keep the heat in and lots of mass in whatever form. And some pipes to get heat in and out via e.g. water. The bigger the container, the smaller its surface area is relative to its volume. So these things can be quite efficient. If you make them large enough, you can store enough energy in the summer to last for months during the winter.

Here's a story about a Dutch retiree who built a prototype using basalt as the thermal mass in his backyard: https://deepresource.wordpress.com/2020/03/08/cesar-seasonal...

  Claimed performance:

  Storage volume: 200-250 kWh/m3

  Storage cost: 2 cent/kWh

  Storage leak: 80% energy still present after 6 months

Ekaros4• 2 years ago

Now what would be suitable material with such phase change around 80 to 110 degree temperature? As that is what effective heating needs. Water with the safe change at 0, is clearly too low as then you could just run ground source or air source heatpumps...

isolli• 2 years ago

The Venera probes used this idea in the 1970s. [0]

One new idea, for additional thermal protection, was the addition of phase-change material. Lithium nitrate trihydrate melts at 30° C, absorbing a large amount of heat, due to its high latent heat of fusion.

[0] http://mentallandscape.com/V_Lavochkin1.htm

latchkey• 2 years ago

Good buddy of mine in Vietnam has been working on a company around this as well:

https://www.alterno.group/

froddd• 2 years ago

The fact I find most fascinating is that they have a local district heating system reusing heat produced from local industry. That’s efficiency on another level.

apexalpha• 2 years ago

I think that's pretty common, no? Here in NL our district heat comes from a chemical refinery a few clicks away. For them the heat is an annoying waste product.

m4rtink• 2 years ago

Here in Brno, Czech Republic, 25% of the city wide heating is provided by the municipal waste incinerator.

There are also a few cities that get heat into their networks from nuclear power plants and something similar is planned in the future for Brno as well.

petters• 2 years ago

Storing heat in huge water tanks has been done for a long time in Sweden

locallost• 2 years ago

Would it make sense to actually store it underground, or are the gains minimal when compared to the costs?

In general, I'm impressed that there's so much research and investment in this field (storing excess renewable energy). I think most people don't realize how much and that the problem of the sun not shining and wind not blowing all the time will be solved much more quickly than most people think is possible.

nimos4• 2 years ago

https://en.wikipedia.org/wiki/Drake_Landing_Solar_Community

There was an experimental community in Alberta, Canada doing this. Seems to be relatively successful as pilot project.

onetimeuse923043• 2 years ago

100MWh = 3.6 * 10^11 joules

sand's heat capacity = 830 J/kg degree C

sand battery size is "13m tall and 15m wide". Assuming most voluminous possible shape that's 13m * 15m * 15m = 2925 cubic meters of sand (100% fill, no account for insulation, etc.)

Dry sand density is about 1600kg/m3

Total weight of sand would be 2925m3 * 1600kg/m3 = 4.7Mkg (4.7kt)

4.7Mkg of sand has a heat capacity of 830J/kg * 4.7Mkg = 3.9 * 10^9 joules / degree C (it takes this much energy to heat up entire battery by one degree C)

So from this, we get that 100MWh of energy would heat up the battery by (3.6 * 10^11 J) / (3.9 * 10^9 J/C) or about 100C.

If we include a different shape (a cylinder), and account for a thick insulation needed, this becomes closer to 200C of temp diff.

I guess it checks out... It is going to be more difficult to estimate heat loss.

But sand is quite expensive so my question is, why sand and not water? Water has 5 times higher specific heat per weight, about 3 times per volume. Water is way cheaper than sand and much easier to find, transport and extract energy from. The only real problem with water is you can only heat it up to 100C.

ametrau2• 2 years ago

They heat the sand to 600c. But you could just use more water. I don’t get it also.

dgacmu• 2 years ago

Interesting! Wonder if it's also due to ease / lower risk of containment. And sand doesn't expand if you accidentally let it freeze, which is again nice from an "it won't rupture" perspective.

As to cost, the article does note that they're reusing crushed soapstone from a local byproduct, so maybe that helps reduce the cost?

That said, their FAQ says it's about heat capacity: https://polarnightenergy.fi/sand-battery

Why do you use sand?
Many solid materials, such as sand, can be heated to temperatures well above the boiling point of water. Sand-based heat storages can store several times the amount of energy that can be stored in a water tank of a similar size; this is thanks to the large temperature range allowed by the sand. So, it saves space and it allows versatile use in many industrial applications.

So perhaps they're also specifically targeting future applications where they would need to supply > 100C heat.

codewench• 2 years ago

Another concern is losses. Water can evaporate, can leak, and tends to corrode fittings.

Sand? If some spills just grab a skid loader and stuff it back in.

mcv• 2 years ago

More water takes more space, and perhaps the higher temperatures make it easier to reuse the heat? And you probably don't want your water to get above 100 degrees C, because then you need to deal with pressure.

Sand is also a really good insulator if I'm not mistaken. That could also be a factor somehow.

merelysounds• 2 years ago

But sand is quite expensive so my question is, why sand and not water?

The article says they will use a byproduct from a local industry, perhaps it's available for cheaper.

"The sand itself will also be sustainably sourced – it’ll consist of crushed soapstone, which is a manufacturing byproduct of another local industry. This material can apparently conduct heat even better than regular old sand.".

onlyrealcuzzo2• 2 years ago

The article says they will use a byproduct from a local industry, perhaps it's available for cheaper.

Cheaper than water?!

captainbland• 2 years ago

They might get quite a good deal on types of sand which are no good for construction but are highly abundant like sea sand or desert sand.

fragmede• 2 years ago

That’s the question, innit. Is there a sand-ologist around here?

squarefoot• 2 years ago

I was about to write just that. Also, desertification is a problem, so they could possibly get free raw material from many places, paying only shipping, and doing something good at the same time.

Pigalowda• 2 years ago

If it’s going to function as an energy source doesn’t it need to run a turbine so it can’t be water? The article said it’s going to just use heat directly so I guess they could use water.

But if ever the need arose it needs to be higher than 100C so it can generate steam for the turbine? Maybe I’m way off, I’m just a guy.

tnjm• 2 years ago

Another point, and I'd love to be corrected here, is that with a container of water you're going to get a ton of convection currents leading to a much sharper heat gradient at the edges, resulting in significant heat losses with the same amount of insulation.

At a guess, and I confess I'm not capable of running the numbers, this offsets the much higher temperature delta of sand.

seanc• 2 years ago

Also, water is constantly trying to leak out of whatever you put it in.

giarc• 2 years ago

Why not water - I wonder if it's because it's in Finland and 6 months a year you have to prevent the water from freezing.

ryukoposting• 2 years ago

You can heat sand above 100C without the sand turning into a gas.

dandy23• 2 years ago

I cannot explain the physics, but a big rock that has basked in the sun is really warm for a long time after sunset. A bucket of water loses its temperature faster.

The higher density of rock probably plays a big role.

onetimeuse923043• 2 years ago

I cannot explain the physics

Here, this is actually the problem.

Water can store many times the amount of energy per volume or mass, per degree Celcius, than rock.

What you see is that rock has much lower thermal conductivity. It can be hot inside but it is not as good at transferring that heat outside. It means when you have hot rock it will stay hot for longer than equivalent amount of water. That because water emits that energy faster.

But put that rock and water in a well insulated vessel and you will find that the properties of the insulation and the vessel will start dominating the process and what counts now is how much energy you can store in the material inside.

pantalaimon• 2 years ago

For water evaporative cooling is a big factor

Tade02• 2 years ago

I can think of several reasons I would choose sand:

-Order of magnitude smaller coefficient of thermal expansion.

-No real risk of phase change - freezing or boiling.

-No problems with corrosion/scale in high temperature. On one hand regular water contains minerals which can build up on the heat exchanger element, on the other demineralized water sucks in carbon dioxide and oxygen from the atmosphere, causing corrosion of steel parts. You would need an airtight container to alleviate this.

Sand is great because it's largely inert in a huge range of temperatures.

onetimeuse923043• 2 years ago

-Order of magnitude smaller coefficient of thermal expansion.

On the other hand the thermal expansion of water does not matter because water, you know, is a liquid -- it conforms to whatever vessel you put it in.

-No real risk of phase change - freezing or boiling.

In a vessel that is meant to store thousands of tonnes of water that is hot and that is very well insulated to store energy for months, there is no real danger that the water will freeze. On the boiling side, water make it easy to monitor the temperature and you just stop adding energy if it starts boiling. Your kettle can do that reliably, we can do this for a huge battery.

No problems with corrosion/scale in high temperature

It is hard to put 5 thousand tonnes of sand in a container and ensure it is dry. There is always going to be water that will be evaporating when you heat the sand in the middle and condensing on the sides that are cold.

There is no possibility of scale when you do not heat water to boiling.

Sand is great because it's largely inert in a huge range of temperatures.

Crushed rock will release water when heated up.

singleshot_• 2 years ago

Ease of transport.

I’ve got a few trucks in which I could transport tons and tons of and but I’d struggle to move more than a few hundred gallons of water at a time. I’d guess most transportation outfits are similar and costs in accordance. Point: sand.

aydyn• 2 years ago

Other considerations, water grows microorganisms and is a solvent. The upside of sand is (presumably) less maintenance.

nimos4• 2 years ago

Been curious if you can't do this with houses generally. Set a temperature range of say 21-25c. Drive the temperature up when there is excess wind/solar (was primarily thinking of EU) then let it fall off.

Obviously works better the better insulated a house is. Has the advantage of turning everything in your home into a thermal battery with the only real cost being furnace controller, potentially even just software. At one point I meant to do the math to figure out the rough storage/efficiency for an average home but never got around to it.

darkerside2• 2 years ago

Real estate is precious. You really want a massive heat battery taking up a lot of living space?

nimos4• 2 years ago

I'm not suggesting adding anything. Homes have lots of stuff in them. Everything in your house becomes a thermal battery - tables, chairs, beds, walls, counters, clothes and so on. Just allow a range of temperatures and when energy is very low cost drive the indoor temperature to the upper range.

Ideally you have a brick/stone home with good exterior insulation.

ametrau2• 2 years ago

It’s more of a sand heat sink. It’s heated up in various ways then the heat is used when it’s needed.

Giant 'sand battery' holds a week's heat for a whole town

Related Stories