Samsung announces first 3nm PDK

https://www.anandtech.com/show/14333/samsung-announces-3nm-gaa-mbcfet-pdk-version-01

by kristianp • 7 years ago

102 39 7 years ago

baybal23• 7 years ago

To add to that, I recently heard that Intel is about to jump the Synopsys ship for Cadence.

I was completely dazzled thinking "what to they get from that?" until it hit me that only Cadence has 7nm TSMC and Samsung workflow ready.

This made me thinking, is Intel finally thinking about doing 7nm tapeouts at TSMC or Samsung?

dfrage• 7 years ago

I remember reading that Intel was having TSMC run off the lowest end Altera FPGAs because Intel's fabs were just too expensive.

Other possibilities off the top of my head might be Cadence being able to do stuff that's now required for these smaller and using EUV lithography nodes, and/or a backup in case their "10nm" never makes it, and their "7nm" having problems or also failing. Embarrassment should be preferable to the worst case alternatives, and we have no reason to believe Intel will be able to regain its ability to move to smaller nodes.

rathel• 7 years ago

only Cadence has 7nm TSMC and Samsung workflow ready.

I think you're not right, unless I am missing something.

https://news.synopsys.com/2018-04-30-TSMC-Certifies-Synopsys...

https://news.synopsys.com/2018-06-22-Synopsys-Custom-Design-...

baybal23• 7 years ago

Well, nice to know that. Nevertheless, Cadence was first to get to 7nm, and is still ahead with never versions of 7nm processes like 7HPC.

To my knowledge, they are the only one who have just anything workable for EUV based processes.

donnietb2• 7 years ago

Can someone elaborate on how this translates to the actual performance of GPU. What is the performance jump (will this allow to run 4k x 4k per eye VR headset) when compared to current GPU generation ?

Today Even with Nvidia 1080 cards running 2k x 2k per eye headsets is not an easy task and beyond a smooth VR experience.

sambe2• 7 years ago

It's right there in the article: 1.35x. That sounds like raw speed though, with actual changes probably depending more on what people do with the new technology.

baq• 7 years ago

article and slides don't give baselines for those percentages: is it 35% more at fixed frequency? fixed power?

donnietb2• 7 years ago

It is a comparison against a 7nm along with 0.65 area die reduction.

Current Nvidia is 12 nm I believe, so the question si what is the possible pixel count bump.

ksec2• 7 years ago

GPU scales really well with transistor count and You can expect about double the performance with best of 7nm, and likely another double for 3nm. So you are looking at 4x the performance.

Of course this does not take into account about TDP, Clockspeed, Memory Speed, Cost of Die Size etc. What is technologically possible may not be economically possible. We are going to need much faster memory, GDDR7? or HBM3, how much would those cost?

And a 3nm ( Whether that is from Samsung or TSMC ) Nvidia GPU will likely be 2022 or 2023 at the earliest.

blattimwind• 7 years ago

And a 3nm ( Whether that is from Samsung or TSMC ) Nvidia GPU will likely be 2022 or 2023.

That seems really optimistic to me.

solotronics• 7 years ago

There is heat dissipation to consider as well so you can't just make a die 4x more dense.

imtringued• 7 years ago

More transistors require more energy. GPUs are already at 300W. Doubling the number of transistors means double the power consumption which means 600W. Smaller transistors are more energy efficient but they can't reduce the energy needed per doubling by 50%. Therefore you end up with a 400W GPU. That's still too high. Energy efficiency is now far more important than raw transistor count.

ricardobeat• 7 years ago

Nearly every existing VR game runs perfectly smooth with a 2080. You won’t get 90fps 4K even with a Ti card, but for FHD we’re well served, price aside.

ItsTotallyOn• 7 years ago

The information in the article is incorrect. The PDK gives more performance OR more power, but not both. Other reporters have this correct, while this article is incorrect.

IanCutress2• 7 years ago

Samsung's own slides state:

Fmax +50% Power @ Fmax -40% Power @ isoperf -50%

Different parts of Samsung aren't talking to each other.

syntaxing• 7 years ago

I'm super curious in the semi technology to create 3 nm layers or beyond. There's not many processes to choose from to begin with thats scalable with adequate uniformity. Do they use some sort of MBE process?!

baybal23• 7 years ago

Rumours heard by me were of apple's tapeout on 7nm being tragically low yield in between 30 to 40% (throwing away half of the wafer,) but also that TSMC eventually got 7nm yields into sane values.

New processes almost always have a yield drop, followed up by recovery, but anything below 50% is really unprecedented.

Apple 12 is not that of a huge chip. It is big for a mobile SoC, but smaller than say a mainstream gaming grade GPU.

I greatly doubt the use of MBE, most likely some regular kind of epitaxy + a lot of process control and swearing to get it right. MBE would've increased cycle times way too much (need for ultra deep vacuum and 0 impurities)

bufferoverflow• 7 years ago

That's pretty wild. Most atoms are 0.1-0.2nm in diameter.

exabrial• 7 years ago

Kinda makes me wonder what the absolute limit is. Is a 3 atom transistor possible?

creatornator• 7 years ago

Going much smaller than we have right now, and you run up against some exotic issues--if you decrease the dielectric thickness, you run the risk of break down between the gate and source/drain under normal operating conditions. Your steady current rating also drops dramatically if the other feature sizes are decreased. I would probably say a 3 atom MOSFET is not possible, since at that scale you can't really have an effective dielectric between the atoms, and the conductors connected to the "single-atom terminals" will have a bulk effect on the behavior.

781• 7 years ago

https://en.wikipedia.org/wiki/Single-atom_transistor

permatech4• 7 years ago

3nm (or any "node" measurement) is not a measure of the entire transistor, only of the smallest feature size.

thfuran• 7 years ago

You can go pretty small: https://www.nature.com/articles/nnano.2012.21

sp3322• 7 years ago

At this point I don't think they physically measure anything on the chip to get that number. It's just an indication of how tightly you can space the transistors, plus a bit of marketing hype. The pics in the article make me wonder if the new gate design is even wider than before, but allows for stacking up transistors which ends up increasing the density to the equivalent of 3nm.

permatech4• 7 years ago

At this point I don't think they physically measure anything on the chip to get that number.

They are measuring the smallest feature size - the smallest shape that is reliably replicated across the wafer. Actually pretty impressive when you think about the lithography behind it.

ip26• 7 years ago

Also critical, the crystal lattice spacing between atoms for silicon is 0.5nm

GuB-42• 7 years ago

It is indeed pretty wild but the "3 nm" name is not an actual distance, it is a marketing term supposed to represent the transistor density. The actual transistors are much larger than that.

For example Intel's 10nm is equivalent Samsung's 7nm. They both have a pitch of around 40nm.

EvgeniyZh• 7 years ago

Any comparison for transistor density (and power consumption) of different manufactures/generations? Though probably they are hiding this as hard as possible, throwing only marketing nonsense on consumers.

elorant• 7 years ago

I was under the impression that at this scale you have quantum tunneling issues.

basementcat• 7 years ago

You have "quantum tunneling" well before this process node. Otherwise, flash memories wouldn't work.

Samsung announces first 3nm PDK

Related Stories