RP2350 PicoDVI Preview

https://github.com/Wren6991/PicoDVI/commit/ca941baf37e3f04738b8e641896d85feb3430385

by fidotron • 2 years ago

194 72 2 years ago

tony-allan• 2 years ago

The RP2040 discussion -- https://github.com/Wren6991/PicoDVI

The new HSTX interface on the RP2350 seems to be squarely targeted at this use case (video output) and doesn't require the use of PIO or consuming a ton of CPU cycles. There's a nice write up on the capability here: https://www.cnx-software.com/2024/08/15/raspberry-pi-rp2350-...

phire5• 2 years ago

The main advantage of the SIO TMDS encoder, is that it allows you to output TMDS on any GPIO, instead of the eight that the HSTX is restricted to.

And they allow an easy upgrade path for projects that were already bit-banging DVI on the rp2040. Other than those two advantages, I don't think there is any advantage to the SIO TMDS encoder over the HSTX TMDS encoder.

I get the impression that the SIO TMDS encoder was added to the design first, and there wasn't a good reason to remove them after the introduction of HSTX.

jauntywundrkind4• 2 years ago

Isn't hstx mainly good for streaming out? My naive guess would be that it wouldn't have as much transceiver offload capabilities, like what the SIO I naively guess would be good for.

The nice part about using SIO seems to be that you can do the tdms encoding there. With hstx you need the output bitstream in the right format already which seems like you might be back to needing the CPU to do the encoding.

phire5• 2 years ago

HSTX has a built in TMDS encoder, and as far as I can tell, it has all the functionality of the SIO TMDS encoder.

You can configure it to directly consume any line buffer with any pixel format, from 1 to 8 bits per color channel. It even supports formats with different numbers of bits per channel like 8-bit RGB322 and 16-bit RGB565.

Palomides• 2 years ago

can the RP2350 do a higher resolution? it would be a neat option for some retrocomputing stuff if so

raphlinus• 2 years ago

My understanding is that the HSTX can do twice the bit clock as the frequency of the CPU, as opposed to 1x for RP2040. So 800x480 (60Hz) is possible with no overclocking (295MHz bit clock) and Luke said [1] he got 1280x720 50Hz with overclocking (530MHz using CVT-R according to the video timings calculator [2]).

[1] https://mastodon.online/@wren6991@types.pl/11292855122145752...

[2] https://tomverbeure.github.io/video_timings_calculator

jauntywundrkind4• 2 years ago

I wonder what res/refresh Display Stream Compression (DSC) would bring this up to, if this were DisplayPort (instead of DVI)?

phire5• 2 years ago

Probably.

Especially with the HSTX block which can apparently output at double the system clock (while the rp2040 was limited to 1/10th of the system)

If my rough math is correct, it should be possible to do output 720p 60hz video with an overclock to ~320Mhz. Though, actually generating that many pixels might be hard when you have nowhere near enough memory.

I would love to see some solid infomation about how well the rp2350 overclocks, apparently 300mhz is easy. 60hz 1080p is almost certainly out of reach, it would require something like a 700mhz overclock, but 30hz 1080p is probably viable.

jsheard3• 2 years ago

Though, actually generating that many pixels might be hard when you have nowhere near enough memory.

Even if you don't have enough memory or CPU time to render true 720p, it's nice to be able to output 360p or 240p inside a 720p container with each pixel and line duplicated two or three times. Doing it that way gives you nice crisp pixels rather than the blurry mess the displays internal upscaler would probably produce. You can even insert blank lines to get a faux-CRT-scanline effect.

vardump• 2 years ago

while the rp2040 was limited to 1/10th of the system

Isn't RP2040 capable of outputting at system clock rate?

dmitrygr• 2 years ago

The two chips I have will both run at 350MHz with Vcore at 1.3V. No glitches seen. I am not sure how safe it is to run with that Vcore for long though. Probably fine. Stock Vcore will take you to 300 seemingly on all instances of rp2350

kristianp2• 2 years ago

generating that many pixels might be hard when you have nowhere near enough memory.

Sounds like an application for vector graphics!? Then you're in the position of having to write a high performance rasterizer.

ironhaven• 2 years ago

What kind of retro computing are you doing that would work well with high definition (720p). Standard definition I believe only started to be limited around 2007 when Xbox games like Dead Rising had captions that where too small to be legible on SD tvs

MBCook• 2 years ago

I think a link to the repo instead of the change set might be better.

kelnos• 2 years ago

I had no idea what this was, ended up clicking around to the README, and found it quite the enjoyable read.

sitkack• 2 years ago

This is amazing, not only did they port from the 2040 to the 2350, but they also ported all the functionality they could support over to the RV32 cores as well. PicoDVI is usable no matter what cores one chooses to use on the RP2350. Well done!

jsheard3• 2 years ago

The author is also the creator of the RISC-V core found in the RP2350, you don't get your own core design taped out as an ASIC and then not show it off :p

https://github.com/Wren6991/Hazard3

jakobson14• 2 years ago

Guy is an employee of raspi, so of course he's going to write code that ships chips.

transpute7• 2 years ago

Is it theoretically possible to have 2-way HID (keyboard, mouse) and 1-way video output on a single USB-c cable? It would simplify connection to a KVM or software-emulated display/keyboard/mouse. Low FPS would be enough for dashboards and CLI.

jauntywundrkind4• 2 years ago

There's no current specs for dual directional USB over any cable, afaik. There very well should be.

You could present as a device and offer networking and have usb-ip advertised over multicast on that port. Easy, weekend project at most, would be dead obvious to any practitioner.

USB4 as a packetized protocol really should offer something. I do wish there were like a half speed 2.5Gbit usb4 option, that microcontrollers could have some hope of accelerated bit banging.

FlyingAvatar• 2 years ago

Haven't USB hubs done this since USB 1.1?

BenjiWiebe• 2 years ago

Afaik this is 100% allowed by the spec. Flash drives are bidirectional (in and out). Hubs present multiple devices to the host through one cable.

IDK why it isn't done more often in one device though.

transpute7• 2 years ago

According to Wikipedia, DisplayPort 2.0+ can coexist with USB data on the same cable, https://en.wikipedia.org/wiki/DisplayPort

[2.0] .. using only two lanes on the USB-C connector via DP Alt Mode to allow for simultaneous SuperSpeed USB data and video

[2.1] .. tightened its alignment with the USB Type-C specification as well as the USB4 PHY specification to facilitate a common PHY servicing both DisplayPort and USB4. In addition, DisplayPort 2.1 has added a new DisplayPort bandwidth management feature to enable DisplayPort tunnelling to coexist with other I/O data traffic more efficiently over the USB4 link.

tomcam• 2 years ago

Can someone explain the downvotes?

yonatan80702• 2 years ago

I don't think you can do it direcly.

I recently found the Openterface Mini-KVM [1], which is supposed to allow you plug it into your laptop over USB-C, and some arbitrary system with USB+HDMI. Then, using their host software, view the HDMI display output and send mouse and keyboard inputs with ease.

I haven't tried it, so I can't speak to how well it works, but it sounds promising.

It is a crowdfunded project, so the usual caveats apply

[1] https://openterface.com/

transpute7• 2 years ago

This thread has gone from:

  could exist?
   not possible
    specs imply yes?
     exists as open hw/sw

Thanks so much for the pointer! https://www.crowdsupply.com/techxartisan/openterface-mini-kv...

KVM-over-USB .. macOS, Windows, and Linux [clients], with Android support in development.. HDMI and emulated keyboard/mouse (HID) input.. video up to 1920x1080@30Hz with under 140ms latency.. play target device's audio directly on the host computer.. [send text] from the host to the target device, ideal for copying usernames, passwords.. Switchable USB-A Port.. for transferring files.. or sharing other USB devices.

With USB storage emulation, this approaches BMC remote mgmt, minus network attack surface.

rcarmo• 2 years ago

You can get the RP2XX0 PIO to control an extra USB host port. I've been keeping tabs on RP2040 resources: https://taoofmac.com/space/hw/rp2040

u8080• 2 years ago

Yes, this theoretically could be done using DP Alt-mode for type-c. It allows up to 4 lanes(commonly 2 lanes) DP signal over typically USB3 assigned lanes. USB2 data lanes are still functional in this mode. https://newnex.com/technology-articles-dp-alt-mode-over-usb-...

g15jv2dp• 2 years ago

This already exists, right now...? I've seen tons of USB hubs with an hdmi output and several USB ports that can be used concurrently. Hell I'm using one right now. Are you asking about something else?

transpute7• 2 years ago

This is for connecting an SBC to a laptop via one USB-c cable. The laptop emulates a display and sends kb/mouse events to the SBC.

Another comment pointed out a $100 board that can tunnel USB data + video on one cable.

silon42• 2 years ago

You can easily have PD+DP+USB (but limited to 2.0).

wrycoder• 2 years ago

Bitbanged DVI on the RP2040 Microcontroller

sylware5• 2 years ago

I wish the RP2350 would include a fuse to disable for good the ARM cores for those who want only the risc-v cores (and maybe not pay ARM royalties on those chips).

jsheard3• 2 years ago

See pg.1259 in the datasheet, the ARM_DISABLE fuse does exactly that. Putting that in was a smart move because it means they can always make a RISC-V-only variant of the chip without having to tape out new silicon - they just have to blow that fuse at the factory.

londons_explore• 2 years ago

I'm not sure "arm-core-disabled-by-fuse" is gonna be sufficient to persuade arms legal department to stop charging royalties...

sylware5• 2 years ago

Good!

Upon buying a board with a RP2350, do you know of a reseller who burns the fuse before shipping it to you (and don't pay ARM royalies on that sale)?

TaylorAlexander2• 2 years ago

One imagines that at some point they will release a pure risc-v chip, once community adoption of the new RP2350 cores is widespread.

sylware5• 2 years ago

It means the chip CPU cores won't be tied to ARM PI enforcement, and won't have to pay for the license to implement ARM ISA (or implement ARM core design).

kristianp2• 2 years ago

In case anyone missed the blog post about the Raspberry Pi Pico 2, here it is:

https://www.raspberrypi.com/news/raspberry-pi-pico-2-our-new...

It has quite a list of products already created by their partners.

peterburkimsher• 2 years ago

If anyone wants a PicoDVI sock or 4, I had 5 PCBs manufactured and am only using one.

I wanted to put the HDMI connector onto the PCB itself, so I could avoid soldering the very small pin pitch. So I took some measurements and did my first KiCad project!

https://forum.kicad.info/t/hdmi-pcb-edge-connector/48358/9

Just send me an email if you're interested in having one, and I'd be happy to post it to you. The resistors are already populated, too, you just need to solder on the Pico using the through-hole connections.

amelius3• 2 years ago

Is there any way to select between two HDMI signals?

I have an nVidia Jetson but its boot sequence turns off the HDMI output at some point. It would be nice if I could show a placeholder screen while the Jetson is booting. Would something like that be possible by using this RP2350 board?

ale42• 2 years ago

Not directly because it can't handle retransmitting the existing HDMI signal. You probably need to add a HDMI/DVI switch IC like this one: https://www.analog.com/en/products/ad8196.html

psd1• 2 years ago

I've tried a few commercial hdmi switches, to share a monitor between machines. The switch time is long and the monitor doesn't reliably wake up. Perhaps it's related to eDID?

Do you know how that chip is for real-world usability?

dezgeg• 2 years ago

I'd be surprised if that was not fixable in the Jetson with pure software changes.

amelius3• 2 years ago

Perhaps but I don't have time to familiarize myself with their boot architecture. Also it might be different in their next version.

phkahler• 2 years ago

It says 60 percent of CPU cycles on one core with the other core free. What does the available 40 percent of the one core look like? I'm assuming its got some high frequency interrupts going that can't be disturbed? What restrictions are on using the remaining capacity of the one core?

RP2350 PicoDVI Preview

Related Stories