Emulator of Original Dell Charger Using ATTINY85

https://github.com/KivApple/dell-charger-emulator

by tentacleuno • 4 years ago

125 56 4 years ago

bavell2• 4 years ago

I have a strip of ATTINY85's at hand for misc electronic projects and they've been really great for beginner-level circuits and learning embedded programming. I'm a dev by trade but have a bit of electronics knowledge and these are cheap enough to not worry about frying them and still get the job done.

ericwood• 4 years ago

They're such a nice starting place for embedded dev! I'd messed around with Arduino things for a long time, and recently started messing with the chip itself without the abstraction. The ATTINY series is powerful enough for many things while having a relatively small and easy to work with footprint (from a physical and register standpoint). It's actually possible to go through the entire datasheet and understand it, then poke all the right registers. It's also satisfying to be able to plop it onto a breadboard!

I'm excited for the Rust + AVR world to move forward a bit so I can keep playing with it without the currently required hacks :)

auxym3• 4 years ago

In case you're interested, there's a new project underway that aims to make running Nim on AVR (and eventually other micros through BSPs) as easy (but leaner and more performant) as Arduino: ratel.peterme.net

Nim can already run on most MCUs (I've experimented with samd21 and rp2040), it just requires a few compiler flags or linking steps that are not super well documented. Ratel aims to automate that and provide some high level interfaces for hardware access (gpios, etc).

alexk3072• 4 years ago

Awesome work. I just dove into the world of AVR programming and bought a bunch of ATTINY85's. Super easy to work with, extremely versatile, and low power consumption.

titzer2• 4 years ago

Do you use a USB programmer, or did you buy ones that have a USB programmer built in?

unwind• 4 years ago

The ATtiny85 is a rather small 8-bit microcontroller, and controllers in that size range generally don't have peripherals on the complexity level of USB. So no, there are no 85s with USB programming support built in.

Truth be told, the 85:s are a bit old now, it was released around 2005. But even the more modern "[012]-series" [1] don't support USB, it is kind of the point. The linked Wikipedia page says:

ATtiny microcontrollers specifically excludes various common features, such as: USB peripheral, DMA controller, crypto engine, or an external memory bus.

[1] https://en.wikipedia.org/wiki/ATtiny_microcontroller_compari...

alexk3072• 4 years ago

I flashed the Arduino bootloader on mine by using my Arduino Uno as a programmer

tgflynn5• 4 years ago

I assume the purpose of this would be to build a Dell compatible charger but this repo doesn't appear to provide much information on how to actually do that. I get that the microcontroller provides the signalling the laptop needs to identify the charger, but assuming you built this circuit, how would you actually use it to charge a laptop ?

kube-system• 4 years ago

I believe the old Dell chargers simply have a data pin, which I presume would carry the data generated by this project

tgflynn5• 4 years ago

I guess it would also be helpful to know what range of laptops this is for. I was assuming it was for relatively recent models. I have an Inspiron that's about 5 years old and it has a barrel connector for power. It's not obvious that it contains a third pin. I have at times had problems with the laptop refusing to recognize various power adapters though.

dec0dedab0de• 4 years ago

It's a bit over my head, but the schematic in the readme seems to have a shared ground, with one pin going to the attiny microcontroller, and the other going to a generic power source. With a big warning that your power source needs to be up to spec.

tgflynn5• 4 years ago

If the connector on the left represents the output of a generic power supply then I still don't see how you would connect this on the laptop side.

EDIT: On further thought I think that connector must be intended to represent the laptop input and Vcc is the output of a generic power supply (with sufficient voltage and current capacity). It was not clear to me because my Dell laptop doesn't appear to have a 3-pin power connector so maybe this only applies to certain models.

zelon88• 4 years ago

In schematic.png you can see on the left there are 3 pins and the right there are 2 pins. The 3 pins on the left represent the laptop and the two pins on the right represent the power supply. The chip in the middle attaches to the ID pin on the laptop and reports the charger to the laptop.

tgflynn5• 4 years ago

Yes, I was confused because my Dell laptop power input doesn't have 3 wires (unless there's somehow a third wire buried in the barrel connector), so I was assuming that the ID signal is somehow just combined with the actual input voltage.

stavros2• 4 years ago

Looks like you connect the data pin of the ATTiny to the data pin of the charger jack. The schematic only has two components, the ATTiny and a power regulator for it, then the input is charger power and the output is charger power + data.

bxparks• 4 years ago

The ATtiny85 is nice, with 8kB flash, 512 bytes RAM & EEPROM, 5-6 GPIO pins, they are just enough to do something interesting. But I don't use the ATtiny85 as much as I want to, because flashing requires a separate programmer hardware. It's enough friction to get in the way of rapid software iteration. I once made the mistake of inserting the ATtiny85 upside down into the programmer, and it promptly cooked it dead. Lesson learned.

auxym3• 4 years ago

All micros require separate hardware to flash it, no? Some is cheap (stlink), some are a few hundred dollars, but still.

Unless you have a USB bootloader programmed on the chip, but you still need the adapter to flash the bootloader in the first place.

hwh• 4 years ago

An MCU is a chip in a package that just cannot interface with anything your consumer PC or notebook comes with. You'll need an adapter in any case.

That said, lots of current MCUs come with UART, I2C and/or USB bootloaders allowing to erase/program (if not disabled). This bootloader is typically included in factory ROM, not to be programmed by you or a third party.

jononor• 4 years ago

Not at all! Many devices can be flashed over USB, for example. Many STM32 devices come with a bootloader factory programmed in a read only area that implement USB DFU. Many user-provided software bootloaders can do the same on many other devices. Including the attiny85 using bit banging!

And of course with wireless enabled microcontrollers one can update over the air. Nordic NRF5x over Bluetooth for example, or ESP32 over WiFi.

danhor• 4 years ago

Another exception is the esp32-c3, which includes a jtag debugger inside the chip (not on board, inside the same die)

duskwuff• 4 years ago

I think what the parent is getting at is that, because the ATtiny85 has so few pins, programming it usually requires it to be removed from the target circuit.

MarioMan• 4 years ago

The Digispark[1] and its clones use the ATTINY85 and offer flashing over USB via the Micronucleus bootloader[2] using V-USB[3]. It comes at the cost of a significant chunk of flash storage, but the convenience is excellent. Plus, V-USB support means you can emulate all sorts of USB devices. I've used it to build a DIY NES controller adapter, but it's commonly used as a cheap Rubber Ducky[4]. For projects where USB interfacing makes sense, it can be a good fit.

1: http://digistump.com/products/1

2: https://github.com/micronucleus/micronucleus

3: https://www.obdev.at/products/vusb/index.html

4: https://shop.hak5.org/products/usb-rubber-ducky-deluxe

puzzlingcaptcha• 4 years ago

You can use Attiny412 with a simple USB-UART adapter for programming. Half the flash/SRAM but much more modern peripherals. $0.50 a piece, and unlike many other uCs recently tends to be in stock.

russdill• 4 years ago

In circuit programming is just such a huge step forward. You still need separate programming hardware, but you don't need to pop the chip out.

Beyond that, a few hundred bytes is usually enough for a simple bootloader. That tends to accelerate things even more. And writing bootloaders tends to be fun. I've done a tinyusb bootloader on an attiny45 with the user program sharing the v-usb stack in the bootloader and also a CEC bootloader. The CEC one of course took several minutes.

londons_explore2• 4 years ago

I don't understand why people use the attiny85... The Atmega328 based boards have far wider software support in the arduino ecosystem, so you will typically be able to prototype a project in minutes instead of hours, and the dev boards cost the same, but the 328 ones have more of pretty much everything.

The only benefit of the attiny seems to be that you can save a few millimeters of board space, but if that's your concern there are plenty of far smaller, cheaper and more capable microcontrollers in BGA packages.

tpmoney2• 4 years ago

The obvious answer would probably be the size and the dip formfactor. Sure you can get more capable BGA packaged chips, but how many hobbyists have the ability to properly solder in a BGA?

londons_explore2• 4 years ago

The 328 is also available in dip...

bavell2• 4 years ago

I wanted to gain experience in embedded programming at a lower level than Arduino (i.e. pure C & bitbanging). They're dirt cheap and also simple enough that I can read through the whole datasheet and pretty much understand everything.

It's also kind of a fun challenge working within the limitations on both the HW and SW side.

stavros2• 4 years ago

I was intrigued by "dirt cheap" and went to buy a few tens, but they're apparently $2.5 or so each! I can get an ESP8266 for that amount, which has tons more processing power, RAM, space, and has WiFi. I really can't see why I'd use an ATTiny over that, unless the former cost $0.20 or so.

nanomonkey• 4 years ago

The old Dell barrel jack power supplies use 1wire communication to identify the power supply's capabilities. It would likely be cheaper to purchase a compatible 1wire memory module.

Here is an article on reverse engineering the memory module. https://hclxing.wordpress.com/2014/02/06/hacking-the-dell-la...

tentacleuno4• 4 years ago

and the battery will not charge (the picture is from internet but it has almost identical information)

Yikes! I used a no-name charger on my Dell Latitude for quite a while, and it never stopped me from charging. Just annoyed me about it (press F1 to continue on boot) whenever I took the battery out (wiping the CMOS) and didn't turn off the AC warnings in the BIOS. The one I was using didn't have a serial chip in it, so the laptop flagged it as unknown.

flashingleds• 4 years ago

It goes further than warnings though - at least circa 2012 using an unofficial charger (or official charger where this fragile extra wire is broken) would underclock the cpu dramatically. It happened silently, such that I didn’t realize what was happening and why my laptop was so slow until stumbling upon a random forum post about it. I was pretty sour on Dell after that experience.

userbinator• 4 years ago

The original source linked from that article has unfortunately disappeared, but the archive still remembers:

http://web.archive.org/web/20100329110047/http://www.laptop-...

An explanation of (one of) the design flaws:

http://web.archive.org/web/20100412160453/http://www.laptop-...

Not only is it clearly hostile to the aftermarket, but putting a chip that has 12V absolute maximum ratings in an environment where it could easily be shorted to the 19-20V output of the PSU seems almost like "engineered unreliability" to me.

On the other hand, when IBM/Lenovo had to solve the problem of identifying the wattage available, they used a simple and robust solution of a single resistor:

https://www.thinkwiki.org/wiki/Power_Connector#Signal_Pin

https://www.thinkwiki.org/wiki/Power_Connector#Signal_Pin_2

The only improvement I could make upon that scheme would be to make the correspondence between resistance and wattage monotonic, but otherwise it's an example of non-overengineering and aftermarket-friendly solution.

rektide• 4 years ago

I just learned this week that my old Dell Venue 11 Pro's will happily accept 19/20V if given, without any sideband communication. The laptop has a custom Dell charger, and usb-micro input, which could negotiate via a custom protocol to a higher power level.

But folks are reporting that if you make a 20V USB-micro, they'll charge. Sweet. Riskier than this links careful negotiation over 1-wire, but so convenient. I'll probably rip apart one of my usb-c to 20v barrel jacks & make a cable, in case I want to go back to these units. The need for a custom charger has been a huge barrier to ever wanting to use them again, very nice that these old systems will just work, when given power.

kennywinker• 4 years ago

If you connect an unoriginal adapter, the laptop refuses to charge the battery.

I'm generally against capital punishment, but for whatever exec pushed this through - I think we could make an exception.

Evidlo• 4 years ago

See also the from-scratch Thinkpad battery with an ATTiny85: https://github.com/iam4722202468/ThinkpadBattery

Koshkin• 4 years ago

Is this safe though? (Aren't chargers the way they are for a reason?)

Emulator of Original Dell Charger Using ATTINY85

Related Stories