rscott2049

Nothing nearly so complex. Here's the code in question:

  .wrap_target
     irq set 0          ; Signal end of active packet
  start:
      wait 1 pin 2      ; Wait for CR_DV assertion
      wait 1 pin 0      ; Wait for RX<0> to assert, signalling preamble start
      wait 1 pin 1 [2]  ; Wait for Start of Frame Delimiter, align to sample clk
  sample:
      in pins, 2        ; accumulate di-bits
      jmp PIN, sample   ; as long as CRS_DV is asserted
  .wrap

BTW, Sandeep's original code clocked the RX PIO SM at 50 MHz, pushing all the samples to the output FIFO, and relied on the processor getting interrupted at the falling edge of DV to figure out what samples constituted a packet.

I did some further investigating - it's apparently due to not having enough setup time on the RX pio SM. Even though the PIO clocking is fixed at 100 MHz, there are CRC errors at the lower system clocks. I tried changing the delay in the PIO instruction that starts the RX sampling, but that only made things worse (as expected). Also tried disabling the synchronizers with no improvement.

I expect the RP2350 to perform much better in this scenario! At the minimum, one of the DMA channels should be eliminated, and I'm hoping the CRC calculation will get faster.

Fortunately, the receive ISR isn't cracking packets, just calculating a checksum and passing the packet on to LWIP. I wish there were two DMA sniffers, so that the checksum could be calculated by the DMA engine(s), as that's where a lot of processor time is spent (event with a table driven CRC routine).

Wish I could answer that! All I can guess is that the slower processing speed creates a bottleneck in the LWIP stack somewhere...

If anybody is still following this thread, I fixed the problem: sudo ping -f 192.168.1.6 -s 1473 PING 192.168.1.6 (192.168.1.6) 1473(1501) bytes of data. 347751/347752 packets, 0% loss, min/avg/ewma/max = 0.573/0.625/0.628/1.002 ms 375962/375963 packets, 0% loss, min/avg/ewma/max = 0.573/0.625/0.626/1.002 ms 45876717/45876724 packets, 0% loss, min/avg/ewma/max = 0.570/0.626/0.630/3.972 ms ..^C --- 192.168.1.6 ping statistics --- 48237616 packets transmitted, 48237608 received, 1.65846e-05% packet loss, time 31011738ms rtt min/avg/max/mdev = 0.570/0.626/3.972/0.011 ms, ipg/ewma 0.642/0.627 ms

Turns out I wasn't passing the RX data properly to LWIP...

I'm still working on it - hopefully will be on the DECstation2040 github soon. The interface uses the LAN8720/8740 MAC chips, which provide 10/100 Mbit. (I haven't tried 10 Mbit, so no idea if it works or not). FYI, here's a test result: ping -q -i 0.005 192.168.1.6 PING 192.168.1.6 (192.168.1.6) 56(84) bytes of data. 229501/229501 packets, 0% loss, min/avg/ewma/max = 0.063/76.725/88.698/160.145 ms 295393/295987 packets, 0% loss, min/avg/ewma/max = 0.063/76.792/37.003/160.171 ms 295393/296278 packets, 0% loss, min/avg/ewma/max = 0.063/76.792/37.003/160.171 ms

(Above is with killall -s QUIT ping) As you can see, it eventually hangs, and CMSIS reports: target halted due to breakpoint, current mode: Handler HardFault xPSR: 0x61000003 pc: 0x200001c4 msp: 0x20040f40

Agreed. I re-wrote the Rx PIO routine to do a proper interrupt at EOF, and added a DMA driven ring buffer, which eliminated a lot of the hackiness...

Almost correct - the third implementation does generate the clock, but it isn't necessary to drive the clock directly from the system clock, as there are m/n clock dividers available. I use a 300 MHz system clock, and divide down to 50 MHz which works well. (I've also addressed a few other shortcomings of this library, but am not done yet...) Haven't looked at the 10 MHz half duplex mode, though.

I'm assuming you've looked at the pico-rmii-ethernet library? If so, I feel your pain - I've been fixing issues, and am about halfway done. (This is for the DECstation2040 project, available on github). Look for a release in late aug/early sep. (Maybe with actual lance code? Dmitry??) The RP2350 will make RMII slightly easier - the endless DMA allows elimination of the DMA reload channel(s).

Maybe you'd like to help me get this over the finish line? I'm looking at a steep learning curve, trying to write a Lance chip emulator. I have been able to get LWIP to run on the DECstation HW. (Though Rev 2.1 does exhibit some packet drops which I'm looking at. Hopefully, there's some slight difference between the LAN8720a on the Waveshare boards, and the LAN8742 on rev 2.1 that needs some software...)

The DMA Sniffer is part of the RP2040 DMA engine. It can perform a variety of functions on the DMA'd data, including CRCs, accumulation, bit-reversal, etc. I use the accumulation function to increment the address contained in the HyperRAM command packet after each scan line is DMA'd from HyperRAM to the scan line buffer. This allows re-use of the HyperRAM command packet, eliminating the need for a per scan line packet (3 uint_32s per scanline). Important for the emulator, as it runs out of RP2040 RAM (vs. flash).

This project wouldn't exist without Dmitry's excellent project! Having an m0+ assembly language MIPs emulator makes all the difference...

Thanks for the follow! The only other social media accout is on Hackaday.io: https://hackaday.io/project/196769-decstation2040