jmb99

How is “all RAM sold in consumer PCs must be registered ECC” equivalent to age verification laws? I’m not saying I agree with the premise but that is a bit of a leap

ECC DIMMs are available only for the memory speeds guaranteed to work by the manufacturers of CPUs, like Intel and AMD, e.g. for up to DDR5-5600 in UDIMMs or DDR5-6400 in RDIMMs.

This is not true[1]. These DIMMs are not guaranteed to work with all Threadripper CPUs, but they are guaranteed themselves to be stable at their advertised frequencies, which are higher than JEDEC. (And from my experience, 9000-series threadripper is perfectly happy to drive 8-channel 1Rx8 at 7200MT/s.)

AMD (and possibly Intel, I don’t have any experience with their recent offerings) also lets you overclock memory completely on WRX90. So if you buy JEDEC sticks, you’re welcome to try to push them as hard as you can.

[1] https://v-color.net/products/ddr5-ocrdimm-amd-wrx90-workstat...

There are absolutely fast DDR5 ECC DIMMs[1]. Just break out your wallet (and piggy bank, and rainy day fund, and..)

The main reason there aren’t more options here is that a) high-frequency memory usually isn’t sufficiently stable, unless binned, and b) there’s very, very, very little demand.

[1] https://v-color.net/products/ddr5-ocrdimm-amd-wrx90-workstat...

I’ve been running a Supermicro X10SLH-LN6TF as my router, and it’s very well suited for the job. Power use is very high for a home router, but reasonable for a 1U router - especially considering the era it’s from and its capabilities (routing 5-8Gbps per stream depending on firewall config, able to handle a couple active streams, and line rate routing with no firewall).

I wouldn’t suggest anyone buy something like this today for home use, but 6 years ago when I purchased it there were not many 10GbE routers to be had period, let alone for the price ($300 roughly if I remember correctly ). Even considering the cost of power over the last 6 years, I still come out much cheaper than if I’d bought something more power efficient new at the time.

Do you think it’s legal to shoot a firework at someone’s house?

O2 sensor in cars compare the O2 concentration between the outside air and exhaust gases, it needs outside air as a reference

Source?

In ~300k km worth of diy oil changes, I’ve yet to change a crush washer, and yet to have a drain plug leak.

I always replace them on friends’ Toyotas, because they seem more important, but on every car I’ve owned it hasn’t mattered. And if you take the least amount of effort to google “how to change oil on ________” (fill in the blank for your year, make, model), some forum or video will probably tell you exactly what steps to take, including whether or not changing a washer is necessary.

Changing oil requires

a place where you have sufficient access to the vehicle to drain it

Probably the only valid argument for people who park on the street.

the right equipment

One $5 wrench, one $10 filter wrench (optional). One set of ramps ($40), or jack stands ($30) if you already have a jack. One drain pan, $10 (or free if you're resourceful). Total cost max $65. Cheaper if you look for deals, buy used, borrow from a friend. If you can't afford $65 once to save money in the long run while owning a car, you probably should've bought a cheaper car.

the right disposal solutions

Every oil change requires a jug of oil to be purchased. You can drain your used oil into this jug and then dispose of it along with your other household hazardous waste. This is not hard.

Most people who have cars do not have that.

I might believe this for a place to do an oil change, maybe. I struggle to believe most, but I would believe many. Aside from that, if you don't have those things, you are choosing not to have them.

Which is kind of the point. None of these things are hard, at all. The majority of car owners 100 years ago could adjust their own timing, clean distributor points, replace belts, etc. because if they couldn't, they'd be calling for a tow truck every few hundred miles. Those are all harder, and things have only gotten easier with time. If you can't do them, you are choosing not to, because there's an even easier solution - spending more money and getting someone else to do it for you.

I am typing this on my return flight home from a business trip in Delhi. There are many other areas the Indian government needs to be focussing on first.

I had a similar view to you ~2 weeks ago. Spending some time there very quickly made me realize that there’s a lot of other things that are much more pressing.

I’ve tested this recently (this post week). Had a dns entry up and pointing to an nginx server for ~12 hours, zero requests. 17 seconds after the letsencrypt cert was issued, the floodgates opened. Over a dozen of requests per second.

I agree. I ran mid 16s in 8th grade, and was in the 14s in high school, with the only training being whatever we did in gym class. But I do also look at the sheer number of overweight kids these days and figured, well maybe mid-16s is actually a reasonable average point.

Very few mere mortals could run that fast for even 100m.

That works out to roughly a 16.7-second 100m. While certainly not crawling, that would be a fairly average pace for a fairly fit middle- to early-high-schooler with a bit of practice.

Yes that’s insane to maintain for a marathon, but it’s not even remotely out of reach for 100m for most relatively-fit people at some point in their lives.

I’ve mentioned this as an option in other discussions, but if you don’t care that much about tok/sec, 4x Xeon E7-8890 v4s with 1TB of DDR3 in a supermicro X10QBi will run a 397b model for <$2k (probably closer to $1500). Power use is pretty high per token but the entry price cannot be beat.

Full (non-quantized, non-distilled) DeepSeek runs at 1-2 tok/sec. A model half the size would probably be a little faster. This is also only with the basic NUMA functionality that was in llama.cpp a few months ago, I know they’ve added more interesting distribution mechanisms recently that I haven’t had a chance to test yet.

I stopped getting scared of `if` and `of` about a decade ago when I started explicitly saying (in my head) "input file" and "output file" rather than "if" and "of." You still can mess up the order, but imo no more easily than you can swap `cat in > out` for `cat out > in`.

Friends don't let friends use `dd` where `cat` can do the same job.

Technically yes... but I like being able to explicitly set block sizes and force sync writes.

The linked post currently has demonstrated that 6 years in some reasonable-ish condition is perfectly fine.

they might not last one year.

Definitely not a medium to passively store anything long term without power!

Do you have any evidence to back up this claim? I'm much more interested in data than fear mongering.

You can however set the block size to something quite large, which means you write the same random pattern spread out over multiple blocks repeatedly. If you pick an "odd" block size (like say, your native block size multiplied by 47), it's highly unlikely your disk under test will be swapping around "groups of 47 blocks." (I usually just do a nice multiple, like 4K16, but if you're super paranoid a weird multiple should be pretty much good enough). You won't get reporting of which exact* blocks on the drive are failing, but these days, that isn't really useful information - if any blocks are failing, warranty or ditch the drive.

Yes, that’s right, don’t buy any new car, any phone, any television. Hell don’t buy any x86 laptop or desktop computer, since you can’t disable out replace Intel ME/etc.

How is that better?

How does SSH become an arbitrary user without effective root?

How on god’s green earth is `sudo apt install telnet` sufficiently challenging to be a driving factor to creating your own distro??

I have a 21 yo car and a 12 yo car and will eventually have to get something 'modern' (worse) that forces spyware/subscriptions on me just to get from point at to point b

I daily a 30 year old car. There exists a sweet spot of reliability, safety, and comfort (probably the early-mid 2000s) that in theory, you should never have to buy a vehicle outside of, newer or older. There will always be clean old cars in good shape you can buy, you don't need a new vehicle.

Unless you can't buy gasoline anymore. But that's still quite a long ways away imo.

He finally found a safe spot and successfully pitted the car to a stop.

No such thing as a safe spot to PIT someone, ever, let alone while they're asleep at the wheel. This is a great example of why people hate all cops, anyone with two brain cells to rub together would get in front of the car and gradually slow to a stop.

Damn, is this the first time ever the east coast is doing better than Colorado? We’ve had record snowfalls all over Quebec, I spent all day last Friday skiing in a foot of fresh powder. Unheard of on the ice coast*.

*not literally. But still, crazy amount of snow this year so far

I have a decent amount of second hand experience with used cars, through my brother who is a mechanic and spent a number of years working at a used car dealership. Hyundai/Kia is the only company he ever had to do engine replacements for at said dealership, and he did dozens. All under 200k km (frequently right after the extended warranty on the engines ran out, and occasionally on the second or even third engine for the vehicle). These are cars with good service history and otherwise in excellent condition. Sometimes cars they got on trade, sometimes purchased from auctions, sometimes customer cars (after they were sold). No rhyme or reason, just a genuinely bad design that was “fixed” but never fixed.

The only other universally-bad major component is JATCO CVT transmissions. I think his record was an Infiniti QX60 that had 95k km and a blown transmission. Most small vehicle/sedan CVTs he did were in the 160-190k km range, with some lasting as long as 250k km. And of course they were not repairable, since even if parts were available, the entire thing grenades leaving basically nothing left to rebuild.

Point being, “one engine issue due to a manufacturing flaw” is drastically underselling the issue, at best. It is an incorrectly-engineered engine that fails prematurely when built within specification, except when the tolerance stackup lines up in your favour and you perform much more frequent maintenance than prescribed. Oh and the affected engines were manufactured over about 15 years (and there’s signs that their current GDI 4-cylinders are still affected).

though you've got a pretty deep pit yourself, if 240v and generator weren't part of the sump plans and the rack just got to ride along (that's how it worked for me)

Generator was a requirement for the sump pump. My house was basically built on a swamp, so an hour in spring without it means water in the basement. Now admittedly, I spent an extra couple hundred bucks to get a 240V generator with higher capacity than strictly necessary, but it was also roughly the minimum amount of money to spend to get one that can run on gasoline or propane, which was a requirement for me. 240V to the rack cost me $45, most of that cost being the breaker (rack is right next to the panel).

What if someone else is hosting something important on there and my power is out? My concerns are elsewhere, but there's might not be.

I host roughly a dozen services that have around 25 users at the moment, but I charge $0 for them. I make it very clear: I have a petabyte of storage and oodles of compute, feel free to use your slice, and I’ll do my best to keep everything up and available - for my own sake (and I’ve maintained over 3 nines for 8 years!). But you as a user get no guarantee of uptime or availability, ever, and while I try very hard to backup important data (onsite, offsite split to multiple locations, and AWS S3 glacier), if I lose your data, sucks to suck. So far most people are pretty happy with this arrangement.

I couldn’t possibly fathom worrying about other people’s access to my homelab during a power outage. If I wanted to care, I’d charge for access, and I’d have a standby generator, multiple WANs, a more resilient remote KVM setup, etc. But then I’d be running a business - just a really shitty one that takes tons of my time and makes me little money. And is very illegal (for some of the services I make available, at least), instead of only slightly illegal.

Late reply I know, but I wanted to clear up that I don’t want to normalize a 2.5kW homelab. Usually when talking to people about it I refer to it as “insane.” But, having an absolutely insane amount of computer and RAM is fun (and I personally find it genuinely useful for learning, in particular in terms of engineering for massive concurrency) and I can afford the hydro, so whatever. To match the raw compute and RAM with current gen hardware, you only need maybe 500W - you’ll just be spending a shitload of money up front, instead of over time on hydro. (To match my current lab’s utilized performance, I’d need at least 2 servers, one of which with a ~threadripper 7955WX and 256GB of DDR5, and another with an Epyc 9475F and 1TB of DDR5. That would put me somewhere in the neighborhood of $35k? Ish? Costs me about $115/month to run the rack right now (cheaper than my hot tub) and cooling is free in the winter (6~7 months of the year) so the break even is loooooong term. And realistically, $100ish a month isn’t crazy, considering I self host basically everything - the only services I pay for are my VPS to run my mail server, and AWS for glacier S3 for backup-of-last-resort.

Again, not trying to normalize 2500W, most people don’t need that (and I don’t really either), but I do make good use of it.

As for “rewiring the house for 240V”, every house* in Canada and the US is delivered “split-phase” 240V (i.e. 240V with a centre tapped neutral, providing 120V between either end of the 240V phase and neutral or 240V from phase to phase), and many appliances are 240V (dryers, water heaters, stove/ranges/ovens, air conditioners). If you have a space free in your breaker panel, adding a 240V 30A circuit should cost less than $1k if you pay an electrician, and can be DIY’d for like $150 max unless you have an ancient panel that requires rare/specialty breakers or the run is very long. It’s far from the most expensive part of a homelab unless you’re running literally just a raspberry pi or something.

*barring an incredibly small exceptional percentage

I mean, if you’re in the top 3 percent of anything, yes that’s pretty good, but not unbelievably so, especially in the field of chess. If for instance you randomly put together a classroom full of chess players, there’s decent odds one of them is better than top 3%. Two classrooms and it’s almost a certainty.

Put another way, looking at chess.com users, there are ~6 million people who would count as the top 3 percent. Difficult to achieve, yes, but if 6 million people can achieve it, it’s not really a “humble brag,” it’s just a statement.

and wireguard is about as easy a personal VPN as there is.

I would argue OpenVPN is easier. I currently run both (there are some networks I can’t use UDP on, and I haven’t bothered figuring out how to get wireguard to work with TCP), and the OpenVPN initial configuration was easier, as is adding clients (DHCP, pre-shared cert+username/password).

This isn’t to say wireguard is hard. But imo OpenVPN is still easier - and it works everywhere out of the box. (The exception is networks that only let you talk on 80 and 443, but you can solve that by hosting OpenVPN on 443, in my experience.)

This is all based on my experience with opnsense as the vpn host (+router/firewall/DNS/DHCP). Maybe it would be a different story if I was trying to run the VPN server on a machine behind my router, but I have no reason to do so - I get at least 500Mbps symmetrical through OpenVPN, and that’s just the fastest network I’ve tested a client on. And even if that is the limit, that’s good enough for me, I don’t need faster throughput on my VPN since I’m almost always going to be latency limited.

Fairly frequently, 6kVA UPSs come up for sale locally to me, for dirt cheap (<$400). Yes, they're used, and yes, they'll need ~$500 worth of batteries immediately, but they will run a "normal" homelab for multiple hours. Mine will keep my 2.5kW rack running for at least 15 minutes - if your load is more like 250W (much more "normal" imo) that'll translate to around 2 hours of runtime.

Is it perfect? No, but it's more than enough to cover most brief outages, and also more than enough to allow you to shut down everything you're running gracefully, after you used it for a couple hours.

Major caveat, you'll need a 240V supply, and these guys are 6U, so not exactly tiny. If you're willing to spend a bit more money though, a smaller UPS with external battery packs is the easy plug-and-play option.

How bottomless of a pit it becomes depends on a lot of things. It CAN become a bottomless pit if you need perfect uptime.

At the end of the day, it's very hard to argue you need perfect uptime in an extended outage (and I say this as someone with a 10kW generator and said 6kVA UPS). I need power to run my sump pumps, but that's about it - if power's been out for 12-18 hours, you better believe I'm shutting down the rack, because it's costing me a crap ton of money to keep running on fossil fuels. And in the two instances of extended power outages I've dealt with, I haven't missed it - believe it or not, there's usually more important things to worry about than your Nextcloud uptime when your power's been out for 48 hours. Like "huh, that ice-covered tree limb is really starting to get close to my roof."

Scraping text across the entire internet is orders of magnitudes easier than scraping YouTube. Even ignoring the sheer volume of data (exabytes), you simply will get blocked at an IP and account level before you make a reasonable dent. Even if you controlled the entire IPv4 space I’m not sure you could scrape all of YouTube without getting every single address banned. IPv6 makes address bans harder, true, but then you’re still left with the problem of actually transferring and then storing that much data.